Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Front doors

Adjusting a Front Door: What to Do When It Is Hard to Close, Draughty or Sticks

7 minutes read

Adjusting a front door helps in most cases where it is hard to close, draughty or sticking: the hinges let you align the leaf in height and sideways, and the keeps let you regulate the compression against the seal. Often a hex key and a little patience are enough. For motor locks, burglar-resistant doors or during the warranty period, you should call a specialist firm.

Adjusting a Front Door: Symptoms and Causes

Before you pick up a tool, narrow down the cause:

Symptom Possible cause Where to adjust
Door scrapes on the floor or threshold at the bottom leaf has dropped height adjustment on the hinges
Door rubs the frame at the side leaf sits offset sideways side adjustment on the hinges
Draught at a corner, seal not making contact too little compression, slight warping keeps or compression
Door closes only with force, key turns stiffly too much compression, bolts do not meet the keeps keeps, lubrication if needed
Door swings shut or open by itself frame or leaf not plumb hinges, if necessary correction of the fitting
Latch does not engage keep offset move the keep

The cause is often seasonal: in winter the outside is cold and the inside warm, and the leaf bows slightly. That is physically normal and permissible within limits; see warping in front doors. A well-adjusted door compensates for this through its seals.

Tools and Preparation

  • hex keys in common sizes, often Torx as well
  • screwdriver
  • spirit level, folding rule
  • paper strips for the seal test
  • lubricant as specified by the manufacturer (usually acid-free and resin-free oil or grease)
  • your manufacturer's maintenance and adjustment instructions

Important: always change only one setting and then check how it works. That way you can see what has an effect and do not accidentally adjust the door in a different direction.

Step 1: Seal Test

Clamp a strip of paper at several points all round between leaf and frame and close the door. If the paper can be pulled out easily at one point, the seal is not making contact there. If it grips firmly everywhere, the compression is right. You repeat this test after every adjustment.

Step 2: Adjusting the Hinges

Modern front doors have hinges that are adjustable in three dimensions, either surface-mounted or concealed. Typically there are three directions:

  • Height: raises or lowers the leaf. Helps if the door scrapes at the bottom.
  • Side: moves the leaf towards the hinge side or lock side. Helps with rubbing at the side and uneven gap dimensions.
  • Compression on the hinge side: pulls the leaf more firmly against the seal on the hinge side.

Where the adjusting screws are located differs by hinge system. They are often hidden under cover caps. Adjust all hinges evenly so that the leaf is not strained.

Step 3: Keeps and Compression

On the lock side, latch, bolt and the locking points of the multipoint lock engage in keeps in the frame. Many keeps can be moved or have eccentrics with which you regulate the compression:

  • More compression: the door is pulled more firmly against the seal. Helps against draughts but makes closing harder.
  • Less compression: the door closes more easily. Helps in winter when the leaf is moving.

Adjust all locking points as evenly as possible. A single bolt set too tight makes the key hard to turn and strains the lock.

Readjusting Seasonally

Some manufacturers recommend reducing the compression a little in winter and increasing it again in summer. Whether this is intended for your door is stated in the adjustment instructions.

Step 4: Looking After Lock and Hardware

Many closing problems have to do with dirt and a lack of lubrication:

  • Lubricate bolts, pivot hooks and latch with a suitable lubricant.
  • Treat the profile cylinder only with the product approved by the manufacturer, since unsuitable oil can gum up the cylinder.
  • Remove dust and wear debris from the keeps.
  • Clean the seals and keep them supple with a care product.

After the care work, repeat the seal test.

Special Cases: Door Closer, Bottom Seal, Motor Lock

Door closer: if the door slams too hard into the lock or stays open, the door closer is often to blame. Closing speed and latching action can usually be regulated by valves on the closer body. Turn only in small steps, because the valves are sensitive. If oil has leaked, the closer has to be replaced.

Drop-down bottom seal: on low-threshold doors, a seal lowers onto the floor when the door closes. If there is a draught at the bottom, the trigger point can often be adjusted with a small adjusting pin on the hinge side.

Magnetic seal: if the seal no longer rises properly out of the threshold, dirt or small stones in the guide are often the cause. Clean carefully; do not lubricate unless the manufacturer provides for it.

Motor lock: bolts not extending fully? First check the setting of the keeps, since excessive compression slows the motor. If the fault persists, call the specialist firm.

When to Call a Specialist Firm

  • Motor lock or access system: faults may be electrical or software-related.
  • Burglar-resistant door: a resistance class applies only as long as hardware and adjustment match the tested specification. According to the police, the deep engagement of the bolts and the keeps, among other things, determine the protective effect.
  • Warranty period: do-it-yourself work can make claims harder, so report problems to the fitting firm instead.
  • Door no longer moves within the normal range despite adjustment: the frame may not be seated correctly or may have come loose.
  • Water gets in or the seal is damaged.

Prevention: Keeping the Door Easy to Operate

  1. Service annually: clean, lubricate, seal test.
  2. Lock the door instead of just pulling it shut: the multipoint locking pulls the leaf towards the frame over its whole height.
  3. Use a door stop: prevents the door from hitting the wall or furniture and bending the hinges.
  4. Do not hang heavy loads on the handle.
  5. Canopy: protects against driving rain and direct sun; see canopies and entrance areas.

A New Front Door Instead of Adjusting?

If a door can no longer be kept permanently tight and easy to operate despite correct adjustment, replacement should be considered, especially where security and insulation are out of date anyway. The article on replacing a front door explains the process. The basic principle of adjustment is, incidentally, comparable with that for windows, which is described in the article on adjusting and maintaining windows.

Checklist: Adjusting a Front Door

  • Symptom and cause narrowed down
  • Manufacturer's instructions and suitable tools ready
  • Seal test with paper strip carried out
  • Hinges adjusted evenly in height and side
  • Compression at all keeps matched
  • Hardware cleaned and lubricated, seals cared for
  • For motor lock, RC door or warranty: specialist firm

The easiest way to find a replacement or a new door is through the front doors. Questions about adjusting and maintaining a door you bought from us can be sent to us via the contact page.

Frequently asked questions

Why does my front door close less easily in winter?

Temperature differences between inside and outside make the door leaf move slightly. As a result, bolts and latch no longer engage exactly in the keeps. It often helps to reduce the compression at the keeps a little.

Can I adjust my front door myself?

Simple adjustments to keeps and, on many hinges, can be made yourself with a hex key. Follow the manufacturer's instructions. For burglar-resistant doors, motor locks or during the warranty period, a specialist firm is the better choice.

How can I tell that the front door is wrongly adjusted?

Typical signs are scraping on the floor or frame, a draught at one corner, a key that turns stiffly, a leaf that swings open or shut by itself, and scratch marks on the keeps.

How often should a front door be serviced?

An annual check with cleaning and lubrication of the moving parts is advisable. Follow the manufacturer's maintenance instructions, because they are often a condition of warranty and guarantee claims.

Sources

  1. Prüfinstitut PfB Rosenheim – Differenzklimaverhalten von Türen(opens in a new tab)
  2. Polizeiliche Kriminalprävention – Haus- und Wohnungstür sicher machen(opens in a new tab)
  3. bauhandwerk/BM – Die Haustür: ein Fall für den Gutachter(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Replacing a Front Door: Process, Time and Fitting
Front doors

Replacing a Front Door: Process, Time and Fitting

Replacing a front door step by step: planning, grant application, survey, removal, fitting to RAL principles, handover, and what affects how long it takes.

7 minutes read

Cover image: Front Door Grants 2026: BAFA, KfW and Tax Bonus
Front doors

Front Door Grants 2026: BAFA, KfW and Tax Bonus

Front door funding in Germany 2026: BEG grant via BAFA, tax bonus § 35c, KfW loan 159, the status of KfW 455-E and care insurance (as at September 2026).

8 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy