Snow Load on Pergolas: What the German Snow Load Zones Mean for Your Louvred Roof
7 minutes read
The snow load on a pergola follows from the snow load zone and the ground height of your site. Under DIN EN 1991-1-3 with its German national annex, Germany is divided into zones 1, 1a, 2, 2a and 3; the characteristic snow load on the ground starts, depending on the zone, at 0.65 to 1.10 kN/m² and rises markedly with altitude. For a flat louvred roof, the roof load is calculated from this using a shape coefficient. Your pergola must be designed for this value. This article applies the German standard; if you are in the UK or elsewhere, ask your supplier or engineer which national snow load rules apply at your site.
What snow load means
Snow load is the weight of the snow pressing on a surface. It is given in kilonewtons per square metre (kN/m²). As a guide, 1 kN/m² corresponds to about 102 kg/m². For a pergola of 5 m × 4 m – that is, 20 m² – 1 kN/m² means roughly 2,000 kg of load on the roof.
How much snow it takes depends on its density. Fresh powder snow is light; wet or compacted snow is many times heavier. A figure in centimetres of snow depth is therefore never a reliable yardstick. Weather situations in which rain falls on fresh snow are particularly critical: the snow soaks up the water and the weight rises while the snow depth barely increases.
The snow load zones in Germany
The classification comes from DIN EN 1991-1-3 with its national annex and has been introduced under building supervisory law via the Model Administrative Regulation on Technical Building Rules (MVV TB). The DIBt publishes an assignment of the zones by district and municipality.
| Zone | Minimum value sk | Applies up to ground height | Formula above that (A = height in m) |
|---|---|---|---|
| 1 | 0.65 kN/m² | 400 m | 0.19 + 0.91 · ((A + 140) / 760)² |
| 1a | 0.81 kN/m² | 400 m | Zone 1 value × 1.25 |
| 2 | 0.85 kN/m² | 285 m | 0.25 + 1.91 · ((A + 140) / 760)² |
| 2a | 1.06 kN/m² | 285 m | Zone 2 value × 1.25 |
| 3 | 1.10 kN/m² | 255 m | 0.31 + 2.91 · ((A + 140) / 760)² |
Zones 1a and 2a are increased zones with a 25 per cent surcharge. Zone 3 covers snowy regions, for example in parts of the uplands and the Alpine foothills. For the North German Plain there is also a rule on exceptional snow loads, which a structural engineer takes into account.
From the ground to the roof: the formula
The characteristic snow load sk refers to the ground. On the roof, the roof shape matters:
s = μ₁ · Ce · Ct · sk
- μ₁ (shape coefficient): for flat roofs and roofs with a pitch of less than 30°, μ₁ = 0.8. Louvred roofs are almost flat.
- Ce and Ct: coefficients for exposure and temperature, generally 1.0 in Germany.
For a louvred pergola, then, in simplified form: roof snow load = 0.8 × sk. Safety factors in the structural design come on top.
Pergola snow load: worked examples
| Location (example) | Zone | Height | sk | Roof load 0.8 · sk | approx. kg/m² |
|---|---|---|---|---|---|
| Lowland | 1 | 300 m | 0.65 kN/m² | 0.52 kN/m² | 53 |
| Upland location | 1 | 600 m | 1.05 kN/m² | 0.84 kN/m² | 86 |
| Hill country | 2 | 200 m | 0.85 kN/m² | 0.68 kN/m² | 69 |
| High altitude | 2 | 500 m | 1.60 kN/m² | 1.28 kN/m² | 131 |
| Alpine foothills | 3 | 700 m | 3.86 kN/m² | 3.09 kN/m² | 315 |
The examples show how strongly altitude acts: in zone 3 at 700 m the roof load is roughly six times as high as in the lowland of zone 1. The values are simplified guide figures – a structural engineer carries out the binding design.
Snow drifts at the house wall
A pergola attached to the house wall often lies beneath a higher roof. Snow accumulations can form there – through wind and through snow sliding off the house roof. Such accumulations can locally exceed the basic load markedly. The standard contains its own load assumptions for this. If your house roof drains towards the pergola, be sure to raise this at the planning stage; snow guards on the house roof often help.
What manufacturers' figures tell you
Manufacturers of louvred roofs state the load capacity of their systems in different ways – sometimes in kg/m², sometimes in kN/m², often depending on span and louvre position. Renson, for example, quotes a resistance to snow loads of more than 100 kg/m² with closed louvres for its louvred roofs. That corresponds to just under 1 kN/m².
When comparing, pay attention to three points:
- Reference quantity: is the value a characteristic load or already a design value?
- Dimensions: does the figure apply to the maximum span or only to smaller formats?
- Louvre position: is the load stated for closed or open louvres?
Common misconceptions about snow on the pergola
- "It hardly ever snows here." Design is based not on the average winter but on a rare yet realistic event. Even in zone 1 a wet snowfall can load the roof heavily.
- "The louvres let the snow fall through." Open louvres can collect snow and be loaded unevenly in the process; they can also freeze fast. Stick to the position the manufacturer specifies for snow.
- "A snow sensor is enough protection." Sensors and automation can help but do not replace sufficient load capacity. In a power cut or with icing, the drive may not work.
- "The load is spread evenly." Drifts, snow sliding off the house roof and ice forming in gutters lead to uneven loading.
- "A glass roof can take more." Glass roofs are also designed for a specific load. What matters is always the design for the site, not the material as such.
Consequences for planning
- Reduce the span: shorter louvres and additional posts increase the load capacity. More in the article on the structural design of an aluminium pergola.
- Think about foundations: high snow loads must be transferred safely into the ground through the posts. Which solution suits is explained in the article Foundation for the pergola.
- Winter operation: decide who clears heavy snowfall and how the louvres should be positioned. Practical tips are in the article Pergola in winter.
- Exempt from permission does not mean exempt from structural design: even pergolas exempt from procedure must be structurally sound; Hesse expressly requires a certificate for this.
How to determine your snow load
- Look up the snow load zone of your municipality in the DIBt table.
- Determine the ground height above sea level (NHN), for example via your state's geoportal.
- Calculate sk from the table or formula.
- Multiply by 0.8 for a flat louvred roof.
- Check possible accumulations from the house roof or wind.
- Have the value compared with the load capacity of the system at your dimensions.
- Record the result in writing and keep it with the pergola documentation.
Next step
Once you know snow load zone and height, plan your pergola in the pergola configurator. The configurator automatically adds a centre post as soon as the chosen width exceeds the span limit of the system. Tell us your location when you request a quote so the design matches your snow load – or use the contact form for questions about structural design.
Frequently asked questions
Which snow load zone applies where I live?
The German Institute for Building Technology (DIBt) provides an assignment of snow load zones by administrative boundary as a table. You also need the ground height above sea level, because the load rises with altitude.
What does 1 kN/m² of snow load mean in kilograms?
1 kN/m² corresponds to roughly 102 kg per square metre. A pergola with 20 m² of roof area must therefore, in calculation terms, be able to carry about two tonnes of snow at 1 kN/m².
Should the louvres be open or closed in snow?
The manufacturer decides. Renson, for example, states the snow load capacity of its louvred roofs for closed louvres; iced-up louvres should never be moved.
Do I need to clear snow from a louvred roof?
If the snow depth could reach the design load, yes – carefully and without sharp tools. Wet snow is considerably heavier than powder snow of the same depth.
Sources
- DIBt: Technische Baubestimmungen und Zuordnung der Schneelastzonen(opens in a new tab)
- DIBt: Schneelastzonen nach Verwaltungsgrenzen (Tabelle)(opens in a new tab)
- Friedrich Datentechnik: Basiswissen Schneelast nach DIN EN 1991-1-3/NA(opens in a new tab)
- Renson: Lamellendächer – Produktinformationen und FAQ(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.