Lockable window handles: what 100 Nm means and how much protection the handle really offers
6 minutes read
A lockable window handle rated at 100 Nm withstands, when locked, a torque of 100 newton metres before it can be forced round or torn off. It prevents a burglar from simply opening the window from inside through a drilled hole or a smashed pane. On its own, however, it does not protect against levering the sash open; for that you need security hardware with mushroom cams. The standards named here (DIN EN 13126, DIN 18267) are German editions of the European and national standards; UK buyers will usually find BS EN 13126 and PAS 24 test information from their supplier.
Used correctly, the handle is an important building block, especially on RC2 windows, where it is part of the tested system.
What a lockable window handle is meant to prevent
Burglars have two ways of opening a window via the handle:
- Reaching through: the pane is smashed or a small hole is drilled, then the handle is turned from inside.
- Manipulation from outside: through a drilled hole in the frame, the handle or gearbox is moved with wire or a tool.
A lockable handle blocks both. When locked, it can only be released with a key or, on some systems, with a push button. If force is used anyway, the torque the handle withstands decides.
What 100 Nm and 200 Nm mean
The newton metre is the unit of torque. 100 Nm corresponds to a force of 1,000 newtons on a lever arm of 10 cm, considerably more than can be applied to the handle by hand or with pliers.
The handle manufacturer HOPPE describes its systems like this:
| System | Resistance to twisting when locked |
|---|---|
| Secu100 | up to 100 Nm |
| Secu200 | up to 200 Nm |
According to the manufacturer, both meet the requirements of the standards DIN EN 1627–1630 and DIN EN 13126-3 and carry their own test marks. Other manufacturers offer comparable handles rated at 100 Nm.
Which standards are named
The "Zuhause sicher" network recommends lockable window handles with at least 100 Nm, tested to:
- DIN EN 13126 (hardware for windows), classes 2/3 or 3/3, or
- DIN 18267 with classes FG-S1 or FG-S2.
Look for these details when buying. A lock in the handle says nothing in itself about its resistance.
Why the handle alone is not enough
The German police crime prevention service puts it clearly: lockable window handles alone are not enough because they offer no protection against levering. When levering, the burglar starts at the edge of the sash and pushes it out of the frame; the handle stays locked, but the locking slips out of the keep anyway.
| Type of attack | Lockable handle | Mushroom-head locking |
|---|---|---|
| Reaching through after smashing the pane | protects | does not protect |
| Drilling and manipulating | protects (with drill protection) | does not protect |
| Levering the sash | does not protect | protects |
That is why the handle belongs to a system. On RC2 windows to EN 1627, a lockable handle is part of the tested equipment, together with mushroom cams, security keeps and drill protection. The basics are explained in the article Burglar protection for windows: RC1 to RC3, the locking in the article on mushroom-head locking.
Key-locking or push-button?
There are two designs:
- With key: the handle is locked with a cylinder. Secure, but impractical in everyday use if the key is missing, and in an emergency a locked window can be an escape route that is then blocked.
- With push button and key: the handle locks at the press of a button without a key and can only be opened with a key; on some systems also with a large operating button. This is more convenient.
Consider for each window whether it must serve as a second escape route. There the key should be kept to hand but out of reach from outside.
Retrofitting: how it is done
On most tilt-and-turn windows the handle can be changed in a few minutes:
- Turn the cover rosette: under the rosette at the handle are two screws.
- Unscrew the old handle: set the handle to the tilt position or horizontal and pull it out.
- Check the square spindle length: the spindle must match the gearbox depth. Usual lengths are in the range of a few centimetres; measure on the old handle.
- Check the screw length: screws that are too short do not hold, ones that are too long can block the gearbox.
- Fit the new handle and screw it tight: test the function in all positions.
On older windows or unusual hardware, better ask a specialist firm. If the window has only roller cams anyway, it is worth thinking at the same time about retrofitting the locking, see retrofitting burglar protection.
Handle and tilt position
A lockable handle only protects a closed window. A tilted window is, for a burglar, an open window: through the gap the sash can often be released from the tilt position with a few movements. When leaving the house you should therefore close all windows and, where possible, lock them. Some hardware offers a ventilation-gap position with additional locking; it is safer than the tilt position but does not replace a closed window.
Comfort and accessibility
Security and easy operation are not mutually exclusive. For accessible windows, low operating forces apply under the German ESanMV; handles should be easy to reach. Lockable handles with a push button can be locked with little force. If there are children in the household, consider whether the handle should also serve as a child lock; some models block the turn position but allow the tilt position.
Typical mistakes when buying a handle
- Looking only at the lock: a cylinder in the handle says nothing about resistance to twisting. The Nm rating and the test are what count.
- Wrong square spindle: if the spindle is too short, it does not engage properly in the gearbox; if it is too long, it presses against it and jams.
- Cheap screws: the fixing must also take the torque. Use the supplied screws in the right length.
- Handle instead of hardware: if you change only the handle and leave the roller cams, you have not made levering harder.
- Key at the rosette: a key permanently in the handle or hanging next to it cancels the protection.
Handles on balcony and patio doors
The same principles apply to balcony doors. You should also look for an outside handle shell or pull handle that allows closing from outside without reducing security. Lift-and-slide doors have their own lockable handles, which must match the respective hardware.
Checklist for lockable window handles
- At least 100 Nm resistance; check the test to DIN EN 13126 or DIN 18267
- Always combine the handle with security hardware and mushroom cams
- For escape routes, decide where the key is kept
- Note square spindle length and screw length when retrofitting
- For new windows, order the handle as part of the RC system
- Never leave the key in the handle when you leave the house
- Close windows rather than tilting them when leaving the house
You can configure new windows with lockable handles and security hardware in the configurator. You will find an overview of profiles and equipment in the window range.
Frequently asked questions
What does 100 Nm mean for a window handle?
The figure is the torque the locked handle withstands without being forced round or torn off. A handle rated at 100 Nm resists attempts to twist it with tools much better than a standard handle.
Is a lockable window handle enough as burglar protection?
No. The German police point out that lockable handles alone offer no protection against levering. They only work together with security hardware such as mushroom cams and security keeps.
Which standard applies to lockable window handles?
The Zuhause sicher network names handles with at least 100 Nm, tested to DIN EN 13126 in classes 2/3 or 3/3 or to DIN 18267 with FG-S1 or FG-S2. Some manufacturers also state their own test marks.
Can I retrofit a lockable handle myself?
Yes, on most tilt-and-turn windows it takes two screws. What matters are the right spindle length of the square and the screw length. The handle should match the type of hardware.
Sources
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.