Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Shutters, security & installation

Retrofitting a roller shutter motor: from strap or crank to electric drive

7 minutes read

Retrofitting a roller shutter motor means, in most cases, sliding a tubular motor into the existing shaft and putting the strap or crank out of use. Where the roller shutter box is hard to reach, an electric strap winder in the room is the simpler alternative. What matters are the right torque, the matching shaft size and an electrical connection made by a qualified person. Electrical work in the UK is subject to its own rules (in England, Approved Document P), so have the connection done by a competent electrician.

Whether you control by switch, radio transmitter or app is best decided before you buy, as it determines the motor type and wiring.

Why retrofit a roller shutter motor?

Strap winders are the simplest way to operate a roller shutter, but they have limits. According to the specialist literature, the pulling force on the strap should not exceed 90 N. Large, heavy curtains, for example on balcony doors, are laborious to operate this way, and straps wear out. A motor brings:

  • Comfort: a button press instead of pulling, even with large roller shutters
  • Automation: schedules, sun and wind sensors
  • Security: presence simulation while you are away
  • Gentleness: even winding up and down without jerks, less wear on the curtain
  • Accessibility: operation without physical effort

Two routes: tubular motor or electric strap winder

Criterion Tubular motor Electric strap winder
Installation location in the shaft in the roller shutter box in the room instead of the old strap winder
Access to the box needed not needed
Strap dispensed with stays, wound by motor
Power for large and heavy curtains for smaller, lighter roller shutters
Appearance invisible device visible on the wall
Effort higher lower

The tubular motor is the standard solution. It replaces the strap completely, runs quietly and can also move heavy aluminium curtains. The precondition is an accessible box in which the shaft can be removed.

The electric strap winder is fitted where the manual strap winder used to be. It is quick to install but better suited to lighter roller shutters and leaves the strap as a wearing part.

Choosing the right tubular motor

Shaft size

Tubular motors are slid into the shaft. Common steel shafts have octagonal profiles such as SW 40, SW 50 or SW 60. The motors come in various series to match. For Somfy, for example, the Oximo io series 40 is intended according to the specialist trade for SW 40 shafts, series 50 for shafts from SW 50. Measure the shaft type before buying.

Torque

The torque in newton metres must match the load. Manufacturers provide tables that take account of curtain area, material and shaft diameter. According to the specialist trade, the Oximo io range covers roughly 4 to 40 Nm, in series 50 in steps from 6 to 40 Nm. Principles:

  • A motor that is too weak runs overloaded and switches off via the thermal protection.
  • A markedly oversized motor can exert more force than necessary when it meets an obstacle.
  • Aluminium curtains are heavier than plastic; large balcony doors need correspondingly more torque.

Functions that matter

  • Electronic end positions: the upper and lower positions are learned. Some motors correct the end positions automatically when the curtain expands with temperature.
  • Obstacle detection: if the curtain meets an obstacle while closing, the motor stops and reverses. Rigid shaft connectors are needed for this.
  • Frozen-in protection: the motor detects when the bottom rail is frozen in place and switches off.

Control: switch, radio or smart home

Wired switch

A roller shutter switch or push button controls the motor directly. This is robust and needs no batteries, but requires a cable from the motor to the switch and a power supply. In existing buildings that often means chasing the wall or surface-mounted trunking.

Radio motor

Radio motors need only a power supply at the box. They are operated by battery-powered wall transmitters, which can be mounted anywhere, or by handheld transmitters. With two-way systems such as io-homecontrol, the motor confirms each command and reports its position back. More in the article on Somfy io-homecontrol.

Hub and app

With a hub such as the TaHoma switch, roller shutters can be controlled by app and voice assistants, and schedules and scenarios can be created. According to Somfy, the TaHoma switch supports io, RTS and Zigbee and is compatible with Alexa, Google Assistant and Apple HomeKit.

How the conversion goes

  1. Survey: open the box, note shaft type and length, curtain size and material. Check that the shaft runs freely and the bearings are intact.
  2. Choose the motor: shaft size, torque, type of control.
  3. Plan the power supply: where does the cable enter the box? With radio motors, a supply from a nearby junction box is often enough.
  4. Mechanical installation: raise the curtain and secure or remove it, remove the shaft, remove the strap pulley, slide the motor into the shaft with adapter and driver, fit the motor bracket, refit the shaft, fix the curtain.
  5. Electrical connection: by a qualified electrician.
  6. Set the end positions and teach in the transmitters: following the manufacturer's instructions.
  7. Close the strap opening: seal the old opening for the strap in the box cover neatly so that no draught occurs.

Renovate the box at the same time

If the box is open anyway, it is the ideal moment to insulate and seal it. Old boxes in the lintel are often a thermal bridge. If the box is in poor condition or the windows are being replaced anyway, a new frame-mounted roller shutter with a factory-fitted motor may be the better solution.

Common problems after the conversion, and their causes

  • Motor stops too early or too late: the end positions were not learned correctly or the curtain has stretched. Reset the end positions.
  • Motor switches off after several runs: the thermal protection has tripped, often because the torque chosen is too tight or the shaft runs stiffly.
  • Curtain winds crookedly: the shaft is not mounted level or the suspensions are fixed unevenly.
  • Obstacle detection does not respond: the curtain is attached to the shaft with flexible springs instead of rigid shaft connectors.
  • Radio transmitter only responds sometimes: reinforced concrete, metal-coated glazing or long distance attenuate the signal. Place the transmitter closer to the motor or use a repeater or a hub.

Putting costs in realistic terms

Costs depend on the motor type, control, accessibility of the box and the effort for the electrical connection. A radio motor is more expensive than a motor with a switch but often saves laying cable to the switch position. For several roller shutters, ask for an overall quotation that shows materials, installation and electrical work separately.

Special cases

  • No box accessible: electric strap winder or, when retrofitting a new roller shutter, a surface-mounted roller shutter with a motor.
  • Crank drive: the gearbox is removed, the motor is fitted in the shaft; the crank penetration is closed.
  • Very wide elements: with large lift-and-slide doors, two roller shutters or reinforced shafts may be needed.
  • Several roller shutters at once: with radio control, groups can be formed, for example all roller shutters on one floor.

Checklist for retrofitting

  • Measure shaft type and curtain size, note the material
  • Choose torque from the manufacturer's table
  • Decide control: switch, radio or smart home
  • Plan the power supply at the box
  • Have the electrical connection made by a qualified person
  • Insulate and seal the box while you are at it
  • Check the anti-lift device or retrofit one

If you would like to order new roller shutters with a motor straight away, you will find made-to-measure systems in the roller shutters section. Our team answers questions about drives and torques via the contact page.

Frequently asked questions

Can every roller shutter be converted to a motor?

Most roller shutters with a shaft in the box can be retrofitted with a tubular motor if the box is accessible and the shaft fits. Where the box is hard to reach, an electric strap winder in the room can be an alternative.

What torque does my roller shutter motor need?

It depends on the weight of the curtain and the shaft diameter. Manufacturers offer motors in steps, for the Somfy Oximo io range roughly from 4 to 40 Nm. The right torque is calculated from the area and material of the curtain.

May I connect a roller shutter motor myself?

Experienced DIYers can do the mechanical installation. Work on the 230-volt mains, that is, the electrical connection, may only be carried out by qualified electricians.

Radio or switch: which is better?

A switch is simple and reliable but needs a cable to the switch position. Radio motors need only a power supply at the motor; operation is by radio wall transmitter, handheld transmitter or app. For smart home and schedules, radio is the more flexible choice.

Sources

  1. Wikipedia – Rollladen (Antriebe, Gurtzugkraft)(opens in a new tab)
  2. caliso – Somfy Oximo io: Baureihen, Drehmomente, Funktionen(opens in a new tab)
  3. io-homecontrol – The residential radio protocol (Leitfaden)(opens in a new tab)
  4. Somfy – TaHoma switch(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Somfy io-homecontrol: Smart Roller Shutter Control
Shutters, security & installation

Somfy io-homecontrol: Smart Roller Shutter Control

Somfy io-homecontrol explained: 868–870 MHz radio, feedback, AES-128, TaHoma switch, voice control and the difference from RTS, with a checklist.

7 minutes read

Cover image: RC2 Windows: Resistance Classes RC1 to RC3 Explained
Shutters, security & installation

RC2 Windows: Resistance Classes RC1 to RC3 Explained

RC2 windows and the resistance classes under EN 1627: what RC1 N, RC2 N, RC2 and RC3 mean, the resistance times and what the German police recommend.

7 minutes read

Cover image: External Venetian Blinds or Roller Shutters: Which?
Shutters, security & installation

External Venetian Blinds or Roller Shutters: Which?

External venetian blind or roller shutter? Compare light control, heat protection, winter insulation, wind stability, security, blackout and appearance.

7 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy