Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Energy & grants

Warm edge spacers in windows: how they cut heat loss and condensation at the glass edge

6 minutes read

A warm edge spacer in a window is a spacer in the insulating glass that conducts heat considerably less than the aluminium spacers that used to be standard. As a result the glass edge stays warmer on the inside, condensation forms less often at the bottom edge of the pane, and the window's Uw value improves. According to the data sheet from the German Federal Association of Flat Glass, heat losses in the edge area can be cut by more than half this way. For windows that qualify for funding, the warm edge is now practically standard. The funding and legal references here are German; readers in the UK or elsewhere should check their own regulations and schemes.

Where the spacer sits and why it matters

Insulating glass consists of two or three panes joined all round by an edge seal. The spacer is a narrow profile that keeps the panes apart. It contains a desiccant that binds residual moisture in the cavity and is sealed to the panes with sealants.

The problem: the spacer connects the warm inner pane with the cold outer pane. If it is made of aluminium, it conducts a lot of heat outwards, and the glass edge becomes a thermal bridge. Exactly where glass and frame meet, the surface temperature falls. In winter, moisture from the room air then condenses at the bottom edge of the glass.

What counts as a warm edge

The term is not arbitrary. According to the "Warm Edge" data sheet from the Federal Association of Flat Glass, a spacer counts as thermally improved if it meets the criterion Σ(d·λ) ≤ 0.007 W/K, as laid down in DIN EN ISO 10077-1 Annex G and DIN EN ISO 12631 Annex D. In simplified terms: the sum of wall thickness d and thermal conductivity λ of all materials in the heat flow must be small enough.

For tested systems, the Federal Association of Flat Glass publishes BF data sheets with representative Psi values. Prerequisites include tests in accordance with the guidelines of ift Rosenheim.

Materials at a glance

Spacer Construction Psi value (example range)
Aluminium metal profile high, not considered a warm edge
Stainless steel (e.g. thin-walled profiles) thin stainless steel profile approx. 0.056–0.065 W/(mK)
Plastic with metal foil (e.g. Swisspacer Advance) plastic, vapour-tight foil approx. 0.037–0.047 W/(mK)
Plastic with metal-coated foil (e.g. Swisspacer Ultimate) plastic, coated foil approx. 0.030–0.036 W/(mK)
Plastic with stainless steel back (e.g. Technoform) polypropylene, stainless steel approx. 0.038–0.049 W/(mK)
Silicone foam (e.g. Super Spacer) flexible foam approx. 0.029–0.036 W/(mK)

The ranges come from an overview based on published manufacturer data. The actual Psi value depends on the frame material and glass build-up, which is why data sheets exist for combinations of spacer and profile system. The lower the Psi value, the better.

Effect on the Uw value

The Uw value of the window is made up of glass, frame and glass edge. The glass edge enters with its length and its Psi value. That has two consequences:

  • Many small panes, a lot of glass edge: with glazing-bar windows with true glazing bars, or small windows, the warm edge has a particularly strong effect.
  • Large panes: the glass edge is short in relation to the area; the warm edge brings somewhat less but remains important for comfort and condensation protection.

According to the Federal Association of Flat Glass data sheet, Uw values can often be improved more effectively by optimising the edge seal than by changes to the profile. How the Uw value is calculated is explained in the article Uw, Ug and Uf explained.

Condensation at the glass edge: causes and limits

Condensation forms when warm, moist room air meets a surface whose temperature is below the dew point. At the glass edge, three factors come together: spacer, frame and installation situation. The warm edge raises the surface temperature and clearly lowers the risk. But it is not a cure-all:

  • High humidity from cooking, showering, drying laundry or too little ventilation can still lead to condensation.
  • Curtains and deep window sills impede warm air circulation in front of the window.
  • Leaky connections let moist air into the joint between frame and wall. Under section 13 of the German Building Modernisation Act, the building envelope including the joints must be permanently sealed against air leakage.
  • Low room temperature in individual rooms increases the risk.

If you notice moisture on the windows after replacement, you will find tips in the article avoiding mould after window replacement.

Condensation in the cavity

A different problem is misting between the panes. It arises when the edge seal is leaky and the desiccant in the spacer is saturated. This is not condensation in the usual sense but a defect of the insulating glass unit, which must be replaced. More in the article misted pane in the cavity.

Warm edge and funding

For BAFA funding of windows in Germany, a Uw value of no more than 0.95 W/(m²K) generally has to be demonstrated (status: September 2026). The warm edge is not a requirement in itself, but in practice it is almost always needed to reach this value with common profiles and triple glazing, especially with smaller windows with a high edge proportion. Make sure the manufacturer's Uw proof is calculated with exactly the spacer that is delivered.

Retrofitting? Only with new glass

The spacer cannot be exchanged afterwards; it is an integral part of the insulating glass unit. If you renew the glazing in existing frames that are still good, the new glass automatically brings the edge seal you want. When replacing only the glazing, Annex 7 of the German Building Modernisation Act requires a Ug value of no more than 1.1 W/(m²K) for residential buildings. Whether replacing the glass is worthwhile or a new window makes more sense depends on the condition of frame, hardware and seals.

Glazing bars and small panes

True glazing bars create many small insulating glass units and therefore a lot of glass edge. Here the warm edge is particularly important. If you want the look of glazing bars without this drawback, you can choose applied bars with an internal spacer bar. The glass edge then remains limited to the perimeter of the large pane.

Looks: colour and printing

Plastic spacers come in many colours, for example black, grey, white or wood tones. That lets the glass edge be designed to match the frame. Aluminium spacers are usually silvery and stand out more. Colour alone is not a reliable indicator, though: only the statement in the quotation or glass certificate is reliable.

Tip for tradespeople: always record the manufacturer and type of the spacer in the quotation as well as the glass designation. That makes later reordering of individual panes and proof to funding bodies easier.

Checklist for your order

  • Have "warm edge" and the spacer product stated explicitly in the quotation
  • Ask for the Psi value for the chosen profile system
  • Choose the spacer colour to match the frame
  • For funding: manufacturer's Uw proof with warm edge
  • Commission airtight installation

For our windows, you choose the glazing in the configurator; we are happy to answer questions about the edge seal in the quotation.

Frequently asked questions

What is a warm edge in a window?

Warm edge is the term for spacers in insulating glass made of low-conductivity materials, such as stainless steel or plastic, instead of aluminium. According to the data sheet from the German Federal Association of Flat Glass, the criterion Σ(d·λ) ≤ 0.007 W/K must be met.

Does a warm edge really make a difference?

Yes. The Federal Association of Flat Glass quotes a reduction of heat losses in the edge area of more than 50 per cent compared with aluminium spacers. That improves the Uw value and raises the surface temperature at the glass edge.

Does a warm edge prevent mould on windows?

It clearly reduces the risk of condensation at the bottom edge of the glass because the surface stays warmer there. Whether condensation forms also depends on humidity, ventilation, heating and how the window is installed.

How do I recognise a warm edge?

Often by the colour and printing on the spacer in the cavity. Aluminium is usually silvery metallic, while warm edges often come in black, grey or other colours. Only the statement in the glass certificate or quotation is reliable.

Sources

  1. BF-Merkblatt 004 – Warme Kante (Bundesverband Flachglas)(opens in a new tab)
  2. Warme Kante – Wikipedia (Materialien und Psi-Werte)(opens in a new tab)
  3. Wärmedurchgangskoeffizient – Wikipedia (Psi-g, Uw)(opens in a new tab)
  4. Bundesverband Flachglas – Downloads (BF-Datenblätter, Merkblätter)(opens in a new tab)
  5. § 13 GModG – Dichtheit(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Triple Glazing: Is It Really Worth It?
Energy & grants

Triple Glazing: Is It Really Worth It?

Is triple glazing worth it? Double vs triple glazing compared: U-value, g-value, weight, funding, condensation and which glass suits whom.

7 minutes read

Cover image: Window g-Value: Solar Gain and Light Transmission
Energy & grants

Window g-Value: Solar Gain and Light Transmission

Window g-value explained: how solar energy gets through glass, typical values for double, triple and solar control glazing, and how to choose the right one.

6 minutes read

Cover image: Window U-Values: Uw, Ug and Uf Explained
Energy & grants

Window U-Values: Uw, Ug and Uf Explained

Window U-values explained: what Uw, Ug, Uf and Psi mean, how the Uw value is calculated and which values the GModG and BAFA funding require in Germany (2026).

7 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy