Avoiding mould after window replacement: ventilation, humidity and the right details
7 minutes read
Mould after window replacement arises because the new windows are airtight and moisture from cooking, showering and breathing no longer escapes through leaky joints. You avoid it by keeping the relative humidity between 40 and 60 per cent, airing in short bursts several times a day and keeping an eye on cold spots such as reveals and external wall corners. For larger replacement projects, a ventilation concept under DIN 1946-6 is also part of the picture. The recommendations and standards here come from Germany; in the UK, check the ventilation requirements in Approved Document F and your installer's advice.
What matters: it is not the new window that is the problem but the changed balance of moisture and air exchange.
Mould after window replacement: why airtight windows change the indoor climate
Old windows with worn seals provide an unplanned, constant air exchange. That costs heating energy but also carries moisture away. After replacement, this "hidden" air change largely disappears.
At the same time, the coldest spot in the room shifts. It used to be mostly the pane: condensation ran down old glass and showed that the air was too humid. Modern thermal insulation glazing has a much warmer inner surface. The moisture then settles at other cool spots that are not so easy to see:
- External wall corners, especially behind cupboards
- Window reveals and the connection between frame and masonry
- Roller shutter boxes and lintels
- Areas behind curtains and heavy furniture
The consumer advice centre points out that windows and connections, as thermal bridges, cool down more in cold weather. That is where surface moisture rises first.
The critical values: humidity and surface temperature
The German Environment Agency recommends a relative humidity between 40 and 60 per cent. If it stays above 70 per cent for a long period, the mould risk rises considerably.
For building constructions, DIN 4108-2 sets a minimum requirement: under standard conditions (20 °C inside, 50% relative humidity, −5 °C outside), the inside surface must stay at least 12.6 °C, expressed as a temperature factor fRsi ≥ 0.70. If it gets colder at any point, moisture can accumulate there.
Two adjustable factors follow from this:
| Adjustable factor | What you can do |
|---|---|
| Reduce moisture in the room air | ventilate regularly, vent moisture sources deliberately |
| Keep surfaces warm | do not let rooms cool too much, set furniture away from the external wall, professional window connection |
The second factor is partly down to installation. How thermal bridges at the window arise and how to avoid them is covered in the article thermal bridges at the window connection.
Ventilating properly with new windows
The German Environment Agency gives clear recommendations:
- Heating season: two to three times a day for about five minutes per room with the window wide open.
- Bedroom: five to ten minutes after getting up.
- Kitchen and bathroom: five to ten minutes during or straight after cooking or showering.
- Summer: longer periods of 10 to 20 minutes because the temperature difference is smaller. Ventilate cellars and ground floors better at night or early in the morning.
- Cross ventilation: open windows on opposite sides at the same time, which exchanges the air fastest.
You should avoid permanently tilted windows. They exchange little air but cool the reveal and raise energy consumption considerably.
Further everyday rules
- Keep doors to cooler rooms closed so that warm, moist air does not drift into them.
- Close the bathroom and kitchen door when showering and cooking.
- Do not "heat" cool rooms with warm air from other rooms.
- If possible, do not dry laundry in poorly ventilated living rooms.
- Put a thermo-hygrometer in the bedroom and bathroom.
Where the moisture comes from
Moisture is produced in every home all the time, by people, plants, cooking, showering, drying laundry and aquariums. In one household, several litres of water a day end up as vapour in the room air. As long as warm air can absorb a lot of moisture, it stays invisible. If the air cools at a cold surface, it can no longer hold the water, and it condenses.
That explains why mould after window replacement often appears first in certain rooms:
- Bedroom: at night the sleepers give off moisture, and the room is often kept cooler.
- Bathroom: when showering the humidity rises abruptly; without a window or extract, it builds up.
- Kitchen: cooking steam spreads into adjoining rooms if the door stands open.
- Little-used, cool rooms: warm air from other rooms cools here and gives up its moisture to the walls.
A mistake that is often overlooked: the connection
Not every case of mould after replacement is a ventilation problem. If the joint between window and masonry is not sealed airtight on the inside, moist room air flows into the joint and condenses there. The consequences show up as dark streaks at the plaster junction or a damp reveal. Professional installation on the principle "tighter inside than outside" prevents this. More in the article on the three-layer principle in window installation.
When ventilating alone is not enough
If you are out during the day, you cannot ventilate several times a day. For exactly this case, DIN 1946-6 requires "ventilation for moisture protection" that works without the occupants doing anything. The standard calls for a ventilation concept if more than a third of the windows are replaced in a single-family or multi-family house.
If the concept finds that the air change through leaks is no longer sufficient, a ventilation measure is needed. That can range from simple window trickle vents through external wall air inlets to a ventilation system with heat recovery. More on this:
- Ventilation concept under DIN 1946-6 when replacing windows
- Window trickle vents: fresh air without much heat loss
For BAFA funding and the tax bonus under section 35c in Germany, moisture protection is part of the requirements anyway: execution must be airtight and thermal-bridge-reduced, and adequate air exchange must be checked.
Checklist after window replacement
- Set up a hygrometer and read it daily for the first few weeks
- Target: 40 to 60% relative humidity
- Air in short bursts rather than tilting, especially after cooking, showering and sleeping
- Place furniture on external walls a few centimetres away
- Look at reveals and corners regularly in the first winters
- If humidity stays high or first stains appear: have the ventilation concept and connections checked by a specialist
New builds and freshly plastered reveals also give off construction moisture in the first months, so more frequent ventilation is especially important then.
What to do if mould is already there?
Small, superficial spots on smooth surfaces can usually be removed yourself, for example with suitable alcohol-based products. More important than removing it, though, is the cause: as long as the moisture remains, the mould will come back. For larger areas, recurring infestation or damp spots at the window connection, you should call in a specialist firm or expert. Tenants should always inform their landlord before doing anything.
If you are planning new windows, raise the subject of ventilation at the selection stage. In the window range you will find profiles and glazing; with questions about vents and connections, our team can help via the contact page.
Frequently asked questions
Why does mould form after window replacement?
New windows are considerably more airtight than old ones. Moisture from cooking, showering and breathing no longer escapes unnoticed through joints. If it condenses at cool spots such as external wall corners or the window reveal, mould can form.
What humidity is ideal after window replacement?
The German Environment Agency recommends a relative humidity between 40 and 60 per cent. Values permanently above 70 per cent are considered critical. A simple hygrometer helps with monitoring.
How often should I ventilate with new windows?
During the heating season, the German Environment Agency recommends airing two to three times a day for about five minutes per room with the window wide open, plus after showering or cooking. In summer, 10 to 20 minutes are needed.
Does a window trickle vent help against mould?
Trickle vents provide a small, constant basic air change and can be part of a ventilation measure. Whether they are enough on their own is shown by the ventilation concept under DIN 1946-6.
Sources
- Umweltbundesamt – Wie lüfte ich richtig? Tipps und Tricks(opens in a new tab)
- Verbraucherzentrale Energieberatung – Schimmel und Feuchte(opens in a new tab)
- Wikipedia – Wärmebrücke (Mindestanforderung DIN 4108-2)(opens in a new tab)
- Verbraucherzentrale NRW – DIN 1946-6: Lüften nach Konzept(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.