Window U-values: Uw, Ug, Uf and the Psi value explained
7 minutes read
The U-value of a window states how much heat is lost per square metre per degree of temperature difference; the smaller, the better. A window has several U-values: Ug for the glazing, Uf for the frame, the Psi value for the glass edge and Uw for the whole window. For legal requirements and funding, the Uw value counts: when replacing windows in residential buildings in Germany, a maximum of 1.3 W/(m²K) is permitted, and for BAFA funding generally a maximum of 0.95 W/(m²K) (status: September 2026). The legal and funding values in this article are German; readers in the UK or elsewhere should check their own building regulations and schemes.
What the U-value means
The thermal transmittance, or U-value for short, has the unit W/(m²K): watts per square metre per kelvin of temperature difference. A window with Uw 1.0 W/(m²K) loses around 20 watts per square metre at a 20-degree difference between inside and outside. A window with Uw 0.8 W/(m²K) loses only 16 watts under the same conditions.
The four characteristic values of a window
| Value | Stands for | Describes |
|---|---|---|
| Ug | glazing | glazing at the centre of the pane |
| Uf | frame | frame (outer and sash frame) |
| Ψg (Psi-g) | glass edge | additional heat loss at the glass-to-frame junction, depends on the spacer |
| Uw | window | the whole window |
There is also the Ψe value for the thermal bridge between frame and masonry. It is not part of the Uw value but describes the installation.
Ug: the glazing
The Ug value is determined at the centre of the pane according to DIN EN 673. It depends on the number of panes, the coatings, the gas fill and the pane spacing. Typical orders of magnitude:
- Double-glazed thermal insulation glass: Ug around 1.1 W/(m²K), which is also the Annex 7 GModG requirement when replacing only the glass.
- Triple-glazed thermal insulation glass: according to technical sources, typically about 0.5 to 0.8 W/(m²K).
Argon is usually used as the gas fill; krypton insulates better and allows narrower cavities but is more expensive.
Uf: the frame
The Uf value describes the frame and is calculated or measured under DIN EN ISO 10077-2 with a substitute panel in place of the glazing. A typical value given is around 1.3 W/(m²K); modern profiles with many chambers, insulating cores or wide thermal breaks achieve lower values. The frame therefore usually insulates less well than triple glazing.
Psi value: the glass edge
At the edge of the insulating glass unit, a spacer keeps the panes apart. It used to be made of aluminium and conducted a lot of heat away. Today spacers of stainless steel or plastic are used, the so-called warm edge. According to the data sheet from the German Federal Association of Flat Glass, heat losses in the edge area can be cut by more than half this way. More in the article warm edge.
How the Uw value is calculated
The Uw value is determined under DIN EN ISO 10077-1 as an area-weighted figure from the individual values:
Uw = (Ag × Ug + Af × Uf + lg × Ψg) / (Ag + Af)
- Ag = glass area, Af = frame area
- lg = visible perimeter length of the glazing
- Ψg = linear heat loss at the glass edge
An important insight follows: the Uw value is not a fixed product property but depends on the size and division of the window. Manufacturers often quote a value for a standard window of 1.23 m × 1.48 m. A small bathroom window with a lot of frame has a worse Uw value with the same profiles and glass, while a large fixed glazing has a better one.
Example: how glass, frame and edge have an effect
Let us assume, in simplified terms, a window with 1.2 m² of glass and 0.6 m² of frame:
| Variant | Ug | Uf | Glass edge | Result |
|---|---|---|---|---|
| Double glazing, aluminium spacer | 1.1 | 1.3 | high loss | Uw well above 1.1 |
| Triple glazing, warm edge | 0.6 | 1.0 | low loss | Uw below 0.95 possible |
The table shows the trend, not exact values. The binding Uw value for your window is demonstrated by the manufacturer for the specific dimensions.
Which values are required
Statutory requirements when replacing
Since 29 July 2026, the German Building Energy Act (GEG) has been called the Building Modernisation Act (GModG). Under section 36 and Annex 7, the following maximum values apply when replacing or first installing in residential buildings (status: September 2026):
| Component | Maximum value |
|---|---|
| Windows and door-windows | Uw 1.3 W/(m²K) |
| Roof windows | Uw 1.4 W/(m²K) |
| Door-windows with a folding, sliding or lifting mechanism | Uw 1.6 W/(m²K) |
| Replacing only the glazing | Ug 1.1 W/(m²K) |
| External doors | U 1.8 W/(m²K) |
The requirements apply if more than 10 per cent of the relevant component area of the building is affected. Details are explained in the article GEG requirements when replacing windows.
Funding
For BAFA funding of individual measures, a Uw value of no more than 0.95 W/(m²K) generally applies to windows and balcony and patio doors (status: September 2026). The technical minimum requirements of the funding programme are what count; the Uw value must be demonstrated by the manufacturer for the specific window. The Ug value of the pane is not enough.
U-values of doors and special components
It is not only windows that have U-values. For front doors, the U-value is stated for the whole door area; Annex 7 GModG permits a maximum of 1.8 W/(m²K) when replacing. For lift-and-slide doors, a higher limit of 1.6 W/(m²K) applies than for ordinary door-windows because of the more complex construction. There is no separate Uw value for roller shutter boxes and window sills, but they considerably influence heat loss at the connection. A poorly insulated roller shutter box above a very good window can cancel out a large part of the benefit.
What to look for when comparing
- Ask for Uw for your size: values for standard windows are a guide, not a guarantee for your window.
- Check the glass build-up: double or triple glazing, coatings, gas fill.
- Ask about the spacer: a warm edge improves Uw and surface temperature.
- Do not underestimate the frame: with small windows, the Uf value strongly determines the result.
- Think about the g-value too: a low U-value is good, but energy gain from the sun counts as well; more in the article on the g-value.
- Do not forget installation: a good window loses a lot if the connection to the wall is leaky or uninsulated.
Measured value, calculated value, nominal value
Different figures appear in documents. The Ug value of the glazing is calculated as a nominal value under DIN EN 673 and rounded to one decimal place. The Uw value is either calculated for the specific window or taken from tables. The manufacturer's declaration of performance contains the value you can rely on. Be careful with advertising claims such as "Uw as low as 0.7": the "as low as" usually refers to the best possible specification and size, not to your window.
Checklist
- Set a target value: statutory minimum (Uw 1.3) or funding (Uw 0.95)
- Request the Uw proof for the ordered size
- Plan triple glazing with a warm edge for windows that qualify for funding
- Commission airtight, insulated installation
In the configurator you choose profile and glazing and see the effect on price. Our windows offer profile systems from different manufacturers for different requirements. Whether triple glazing is worthwhile for you is explained in the article double or triple glazing.
Frequently asked questions
What is a good U-value for windows?
When replacing windows in residential buildings in Germany, the Uw value must be no more than 1.3 W/(m²K) under Annex 7 GModG. For BAFA funding, a Uw of no more than 0.95 W/(m²K) is generally required. Good windows with triple glazing come in below this (status: September 2026).
What is the difference between Uw and Ug?
Ug describes only the glazing (g for glazing), Uw the whole window (w for window) including frame and glass edge. The Uw value is therefore usually higher than the Ug value and depends on the window size.
Why does a small window have a worse Uw value?
With small windows the frame proportion is larger. Since the frame usually insulates less well than triple glazing and extra losses occur at the glass edge, the Uw value rises as window size falls.
Is the Ug value of the pane enough for funding?
No. For funding and for the statutory requirements when replacing windows, what counts is the Uw value of the whole window. Only when replacing just the glazing does Annex 7 GModG apply a Ug value (1.1 W/(m²K)).
Sources
- Wärmedurchgangskoeffizient – Wikipedia (Uw, Ug, Uf, Psi)(opens in a new tab)
- Anlage 7 GModG – Höchstwerte der Wärmedurchgangskoeffizienten(opens in a new tab)
- GModG-Infoportal: Fenster und andere transparente Bauteile(opens in a new tab)
- BF-Merkblatt 004 – Warme Kante(opens in a new tab)
- Isolierglas – Wikipedia (Ug-Werte, Gasfüllungen)(opens in a new tab)
- BAFA – Einzelmaßnahmen an der Gebäudehülle(opens in a new tab)
- Fenster-Förderung 2026: Uw-Anforderung (energiefoerderrechner.de)(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.