Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Window profiles

Window Glazing Bars: True, Applied and Internal Bars Compared

6 minutes read

Window glazing bars come in three types: true glass-dividing bars that actually divide the pane into separate sections, applied bars, usually Vienna bars with a spacer in the glass, and internal bars in the cavity between the panes. True glass-dividing bars look the most authentic but are the most laborious; internal bars are the easiest to maintain. The Vienna bar is the common compromise for older homes. Which type suits depends on heritage requirements, the look you want, thermal protection and your willingness to clean.

The three types of glazing bar at a glance

True glass-dividing bar Applied bar (Vienna bar) Internal bar
Construction Bar divides the glass area into individual panes Profiles stuck onto the pane inside and outside, often with a spacer in the cavity Bar profile in the cavity between the panes
Look Historically genuine Very close to the original Flat, bar "behind glass"
Thermal protection More edge and frame proportion Glazing stays continuous Glazing stays continuous
Cleaning Many edges and individual panes Edges at the bars Smooth glass surfaces
Effort Highest Medium Lowest

True glass-dividing bars: the original

With glass-dividing bars, also called "true" bars, the sash consists of several small insulating glass units held by bar profiles. WERU describes them as bars that actually divide the glass area into separate sections and are firmly integrated into the sash.

Advantages: authentic look, especially for listed buildings and historic façades; individual panes can be replaced separately if broken.

Disadvantages: Every individual pane has its own edge seal, and the bar profiles form additional frame proportions. Both increase heat loss. WERU points out that glass-dividing bars need high-quality triple glazing and a warm edge to achieve good values. They are also more laborious to make and to clean.

Vienna bar: the compromise

The Vienna bar combines applied profiles on both sides of the glass with a spacer in the cavity directly under the bar. From outside and inside, this gives the impression of a real division even though the pane is continuous. According to fensterblick.de, this variant is simpler, and so cheaper, to make than glass-dividing bars.

Advantages: convincing look, continuous insulating glazing, and according to WERU no additional thermal bridges from the bar itself.

Disadvantages: The applied profiles form edges where dust collects; when cleaning, you have to work around them.

Internal bars: low maintenance

Internal bars, often called "Helima bars" after a well-known manufacturer, sit only in the cavity of the multiple glazing. The glass surfaces stay smooth inside and outside.

Advantages: very easy cleaning, no change to the outer glass surfaces, available for uPVC, timber and aluminium windows.

Disadvantages: The bar looks flat and visibly lies "behind glass". With large panes, the profiles can rattle; WERU names transparent buffers as a countermeasure.

Glazing bars and thermal protection

When replacing windows in residential buildings in Germany, under Annex 7 of the Building Modernisation Act (GModG) a maximum of Uw 1.3 W/(m²K) applies (as of September 2026); readers elsewhere should check their local requirements. Glazing bars can affect the Uw-value:

  • Glass-dividing bars increase the proportion of frame and glass edge in the window, so the Uw-value rises.
  • Vienna bars hardly change the glazing; according to WERU, the bar creates no additional thermal bridges.
  • Internal bars leave the glazing largely unchanged; fensterblick.de notes generally that bars can slightly worsen thermal protection and reduce light entry.

When getting a quote, ask for the Uw-value of the specific window with bars, not the value without bars; especially with glass-dividing versions, the difference can be relevant. How Uw, Ug and Uf relate is explained in Uw, Ug, Uf: the U-values of a window.

Bars, bar width and light entry

Every bar takes away glass area. On a small window with many panes, the loss of light can be noticeable; on large windows with a simple cross division, it hardly matters. Some practical considerations:

  • Few, slim bars preserve the character without darkening the room.
  • North-facing sides benefit particularly from as much glass area as possible; a sparing division is worthwhile here.
  • Fanlights can be emphasised with bars while the main sashes stay clear.
  • Floor-to-ceiling elements often look calmer with a horizontal bar at parapet height and give visual support.

Transoms and mullions are not glazing bars

Not every line in the window is a glazing bar. A transom is a horizontal and a mullion a vertical frame profile that divides the window into several sashes or sections. Both are load-bearing parts of the frame and have nothing to do with the question of glazing bars. If you want a double-sash window without a central mullion, the solution is the double-leaf window with a meeting stile (Stulpfenster); the differences are explained in Window opening types.

Glazing bars in old buildings and heritage protection

Glazing bars shape the face of historic façades. For listed buildings or in conservation areas, the heritage authority often prescribes the division, bar width and profiling. Not infrequently, glass-dividing bars or Vienna bars of a particular width are required; internal bars are often not accepted there. Clarify this before ordering. What else matters for windows in older buildings is covered in Window profiles for older buildings.

Planning the division properly

  • Follow the proportions: Take your lead from historic photographs or surviving original windows.
  • Bar width: Slim bars look more delicate, wide ones more rustic.
  • Continuous lines: With multi-sash windows, the bars should line up at the same height.
  • Colour: Bars in the frame colour look calm; different colours set accents.
  • Inside and outside: With two-tone windows, the applied bars should also take the respective frame colour inside and outside.

Care and cleaning of windows with glazing bars

The cleaning effort differs markedly:

  • Glass-dividing bars: Each pane is cleaned individually, and the corners at the bars take patience. A small, soft squeegee and a non-abrasive microfibre cloth help.
  • Vienna bars: The applied profiles are wiped with the frame; do not spray glass cleaner directly onto the bonded joint but put it on the cloth.
  • Internal bars: Cleaning as for an ordinary pane.

On timber windows with glass-dividing bars, the bars belong in the regular check of the paintwork, because rainwater stands longer on the horizontal tops of the bars. Care advice is in Wooden windows: assessing the maintenance effort.

Which bar for whom?

  • Listed building or high-quality refurbishment: glass-dividing or Vienna bar as specified.
  • Period look with good thermal protection: Vienna bar.
  • Country-house style with little maintenance: internal bar.
  • New build with modern architecture: usually no bars at all, possibly individual transoms.

Checklist for windows with glazing bars

  1. Clarify heritage or design requirements.
  2. Decide the type of bar, width and division.
  3. Ask for the Uw-value with bars.
  4. Match the colour of bar and frame.
  5. Assess the cleaning effort realistically.
  6. For several windows on one façade: plan division and bar heights uniformly.
  7. View a sample or reference window before ordering all the windows.

Configure windows with glazing bars

In the configurator you set the division, bar type and colour and see the effect directly on the window. You will find the full range on the windows page.

Frequently asked questions

What types of glazing bar are there?

A distinction is made between true glass-dividing bars, which actually divide the pane into separate sections, applied bars, often as Vienna bars with a spacer in the cavity between the panes, and internal bars that sit only between the panes.

Do glazing bars worsen thermal insulation?

True glass-dividing bars bring additional edge and frame proportions into the window and so more heat loss. Applied and internal bars hardly change the glazing itself; with internal bars, the glass surface stays smooth on the outside.

Which glazing bars suit an old or period house?

For the most authentic look, glass-dividing or Vienna bars are chosen. For listed buildings, the heritage authority decides which version is permissible.

Are internal bars easier to clean?

Yes. Because they lie between the panes, the glass surface stays smooth inside and outside. Applied and glass-dividing bars, by contrast, have edges where dust collects.

Sources

  1. WERU: Sprossenfenster – Sprossenarten im Überblick(opens in a new tab)
  2. fensterblick.de: Sprossenfenster(opens in a new tab)
  3. Anlage 7 GModG – Höchstwerte der Wärmedurchgangskoeffizienten(opens in a new tab)
  4. GModG-Infoportal: Fenster und andere transparente Bauteile(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy