Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Shutters, security & installation

Adjusting and maintaining windows: how to look after hardware, seals and frames properly

7 minutes read

Adjusting windows mainly means setting the contact pressure via the eccentric locking cams and, for sashes that rub, correcting the position at the corner hinge and the stay. On top of this comes regular maintenance: lubricate moving hardware parts, check the keeps, clean and care for the seals. Specialists recommend an interval of one to two years for this, annually for heavily used windows.

Well-adjusted windows close easily, are airtight, insulate as planned and keep their burglar resistance.

Why windows need readjusting

Even a perfectly installed window changes over time:

  • Settlement: heavy sashes with triple or security glazing sink minimally.
  • Temperature: frames expand in summer and contract in winter.
  • Seals: they lose elasticity over the years.
  • Use: frequent opening and tilting stresses hinges and stay.

If you compensate for these changes regularly, you prevent small deviations from turning into damage. High-quality hardware is designed for many opening cycles; one specialist source gives at least 20,000 cycles as a test requirement for good hardware. To reach this life, it needs care.

Typical symptoms and their causes

Symptom Possible cause Remedy
Draught at the frame contact pressure too low, worn seal readjust cams, check or replace seal
Window closes stiffly contact pressure too high, lack of lubrication turn cams back, lubricate hardware
Sash rubs at the bottom sash has dropped correct height at the corner hinge
Sash rubs at the side sideways position has shifted adjust at corner hinge and stay
Handle is hard to turn gearbox dry or jammed lubricate, check adjustment
Whistling noises in wind seal does not sit evenly even out the contact pressure

Adjusting windows: setting the contact pressure

The locking cams, mushroom cams on security hardware, sit on the sash and run into the keeps on the frame when closing. Many cams are mounted eccentrically. If you turn them, the distance to the keep changes, and with it the pressure with which the sash is pressed against the seal.

How to proceed:

  1. Open the window and find the cams on the edge of the sash.
  2. Read off the position; many cams have a marking.
  3. Turn the cam with the right tool, hex key or key depending on the hardware.
  4. Set all cams on one side the same, otherwise the seal sits unevenly.
  5. Close the window and check: can the handle be turned without great effort? Is it airtight?

Important: adjust cams only in small steps and never turn them by force. A trick for checking: trap a sheet of paper between sash and frame and close the window. If it can be pulled out easily, the contact pressure at that point is too low.

Some homeowners set a little more contact pressure in winter and a little less in summer. That is possible but not a must; what matters most is even pressure all round. How mushroom cams are built is explained in the article on mushroom-head locking.

Aligning the sash: corner hinge and stay

If a sash rubs or closes unevenly, its position can be corrected at two points:

  • Corner hinge at the bottom on the hinge side: here you can usually adjust the height of the sash and its sideways position at the bottom.
  • Stay at the top: here the sideways position at the top is adjusted, and on some systems also the contact pressure on the hinge side.

The adjusting screws are often hidden under cover caps. Adjust in small steps and check after each change. Because hardware systems differ, the manufacturer's maintenance instructions help. If the sash sags badly, parts are broken or nothing changes after adjusting, a specialist firm should check; perhaps the packing of the glazing has slipped.

Lubricating and checking hardware

According to specialist information, maintenance covers three points: lubricate moving parts, check contact pressure, check keeps for wear.

  • Lubricating: treat cams, keeps, stay and corner hinge with a suitable acid-free and resin-free grease or oil. Wipe off any excess so that no dirt sticks.
  • Checking: are all screws tight? Are parts bent or broken? Do the cams run cleanly into the keeps?
  • Safety-relevant parts: with damage to the stay or corner hinge, the sash can in the worst case fall out. Do not repair these yourself; call a specialist firm.

Caring for seals

Seals provide wind and driving-rain tightness and contribute to sound insulation. Care extends their life:

  • Clean with water and a mild cleaner, remove dirt from the rebate
  • Treat with a care product for rubber or TPE seals
  • Do not use solvents, cellulose thinners or harsh cleaners
  • Mask the seals when painting the frames; paint makes them hard

If a seal is cracked, hardened or permanently flattened, it should be replaced. On many profiles the seals can be pulled out of the groove and replaced with new ones; what matters is to use the right seal profile.

Frame and drainage

Maintenance also includes a look at the frame:

  • Keep drainage openings at the bottom of the frame clear so that water can run out of the rebate
  • uPVC frames: clean with a mild cleaner, no abrasives
  • Aluminium frames: wash regularly, especially near the coast and on busy roads
  • Timber frames: check the coating for cracks and repaint in good time
  • Installation joints: check inside and outside for cracks in the plaster or detached sealant; they can point to movement or a leaky joint

Window types with special requirements

  • Lift-and-slide doors: clear carriages and track of dirt regularly; do not grease the track unless the manufacturer provides for it. Details in the article on maintaining sliding doors.
  • Burglar-resistant windows: mushroom cams and security keeps must engage cleanly. After adjusting, check that all cams move in fully.
  • Windows with rebate vents: keep air paths clear, do not clog the seal cut-outs with care products.
  • Roof windows: the manufacturers' own maintenance instructions apply here.

Maintenance plan for the whole year

Time Task
Spring clean frames and glass, clear drainage, clean seals
Autumn lubricate hardware, check contact pressure, care for seals
Every 1–2 years complete hardware maintenance, by a specialist firm if needed
After the first winter of new windows check the adjustment, as sashes can settle

After new windows are installed, it is also worth looking at the indoor climate: airtight windows call for conscious ventilation. In winter, the German Environment Agency recommends airing in short bursts two to three times a day. More in the article on avoiding mould after window replacement.

Checklist

  • Keep the hardware manufacturer's maintenance instructions to hand
  • Get the tool for the cams and adjusting screws
  • Check contact pressure with the paper test
  • Lubricate the hardware, check the screws
  • Clean and care for the seals
  • For damage to the stay, corner hinge or glass, call a specialist firm
  • Note maintenance dates, for example every autumn before the heating season

The care requirements also depend on the frame material. You will find an overview of profiles and materials in the window range; for questions about hardware and spare parts, our team can help via the contact page.

Frequently asked questions

How often should windows be serviced?

Specialists recommend servicing the hardware every one to two years, annually for frequently used windows. Moving parts are lubricated, the contact pressure is checked and the keeps are checked for wear.

How do I adjust the contact pressure on a window?

Via the eccentrically mounted locking cams on the sash. Turning the cam with a suitable tool pulls the sash more or less firmly against the seal. Many types of hardware have a marking for the position.

My window sash rubs at the bottom, what can I do?

The sash has often dropped slightly. At the bottom corner hinge and the top stay, the height and sideways position of the sash can be adjusted. For badly sagging sashes or damage to the hardware, a specialist firm should check.

What do I use to care for window seals?

Clean seals with water and a mild cleaner and then treat them with a suitable care product for rubber seals. Solvents and harsh cleaners can damage the material.

Sources

  1. FeBa – Fensterbeschlag: Funktion, Sicherheit, Wartungsintervalle(opens in a new tab)
  2. daku – Pilzzapfen für Fenster: Einstellung des Anpressdrucks(opens in a new tab)
  3. Umweltbundesamt – Wie lüfte ich richtig?(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Measuring Windows: Opening, Check Reveal, Tolerances
Shutters, security & installation

Measuring Windows: Opening, Check Reveal, Tolerances

How to measure windows correctly: masonry opening with and without a check reveal, joint allowance, sill connection and roller shutter, step by step.

7 minutes read

Cover image: Fitting Windows Yourself: Possibilities and Limits
Shutters, security & installation

Fitting Windows Yourself: Possibilities and Limits

Fitting windows yourself: what skilled DIYers can manage, where the limits are, what applies to funding, tax bonus and warranty, with working steps.

7 minutes read

Cover image: Window Installation Sealing: Three-Layer Principle
Shutters, security & installation

Window Installation Sealing: Three-Layer Principle

Window installation sealing: why the joint must be tighter inside than outside, which materials belong in the three layers and which mistakes cause damage.

7 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy