Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Shutters, security & installation

Tighter inside than outside: the three-layer principle for sealing at window installation

7 minutes read

When sealing at window installation, the joint between frame and wall is made in three layers: airtight and vapour-retarding on the inside, insulated in the middle, driving-rain-tight but vapour-open on the outside. The basic rule is "tighter inside than outside", so that no moist room air gets into the joint and any moisture that has penetrated can dry outwards. Mistakes in this order are a frequent cause of mould, draughts and moisture damage after window replacement.

The principle is described in the installation guideline of the RAL Quality Association and ift Rosenheim and applies to new builds and renovation. The guideline and DIN standards cited are German; UK installers usually work under a competent person scheme and the relevant Approved Documents, and the same moisture logic applies, so ask your installer which guidance they follow.

Why the joint is so sensitive

The installation joint is a small cavity between two different components. On the inside there is warm room air with moisture; outside there are wind, rain and, in winter, cold. Two processes make the joint vulnerable:

  • Air movement: if the joint is leaky on the inside, warm, moist air flows in. On its way outwards it cools and the moisture condenses, in the middle of the insulation.
  • Vapour diffusion: water vapour also migrates through materials, from warm to cold. If there is a tighter layer outside than inside, the vapour builds up in front of that barrier.

Both lead to wet insulation that no longer insulates, to mould at the reveal and, in the worst case, to damage to the masonry or timber.

Window installation and sealing: the three layers in detail

Layer Requirement Typical materials
1 – Inside airtight, vapour-retarding, high diffusion resistance membrane tapes, vapour-retarding sealing tapes, sealant on backing rod, plaster connection tapes
2 – Middle thermal and sound insulation, completely filled PU in-situ foam, mineral wool, other insulation materials
3 – Outside driving-rain-tight, windproof, vapour-open compressible tapes to DIN 18542, vapour-open membranes, sealants

Layer 1: the inner seal

It is the most important layer for moisture protection. It must be closed all round, including in the corners and at the window sill. Membrane tapes are stuck onto the frame and later plastered over or stuck to the reveal. Vapour-retarding sealing tapes are applied to the frame before installation and expand in the joint. A sound, clean substrate is important. On uneven masonry, a smoothing coat is often needed before tapes will adhere.

Layer 2: the insulation

The functional layer must be completely filled. Voids are thermal and sound bridges. PU in-situ foam is widespread because it evens out irregularities. It belongs only in this layer, though. Protruding foam is cut off before the inner and outer seals are applied, because the cut surface is open-pored and not airtight. The RAL guideline also requires that the joint seal does not worsen the window's sound insulation by more than 1 dB.

Layer 3: the outer seal

Outside, the joint must keep out driving rain and wind but let moisture from the joint pass outwards. Compressible tapes are pre-compressed, impregnated foam tapes that expand in the joint. They work only within the joint-width range stated by the manufacturer; if the joint is too wide, they no longer seal. Alternatively, vapour-open membranes are stuck in and plastered over.

Multifunctional tapes

There are tapes that combine all three functions in one product: tighter inside, more open outside, insulating in between. They are stuck onto the frame before installation and save work steps. They too need the right joint width and a suitable substrate.

Common mistakes and their consequences

Mistake Consequence
Foam only, no tapes draughts, moisture in the joint
Silicone outside, nothing inside joint tighter outside than inside, condensation
Inner membrane open at the corners local air movement, mould at the reveal corner
Compressible tape in too wide a joint driving rain gets in
Window sill connection not sealed water runs under the frame
Foam covers tapes tape cannot expand, sealing ineffective

The consequences often show only after the first winter, when moisture has condensed in the joint and shows at the reveal as a dark edge or flaking paint. The cause can then usually be fixed only by opening the joint, far more laborious than careful execution from the start. How moisture and thermal bridges at the window are connected is covered in the article on thermal bridges at the window connection; what occupants can contribute themselves is in the article on avoiding mould after window replacement.

New build and renovation: different challenges

In a new build, openings are mostly true to size, reveals level and insulation planes known. The sealing can be planned cleanly, often with pre-fitted multifunctional tapes or with membranes that are later tied into the wall's airtightness layer. What matters here is coordination with other trades: the window's inner membrane must connect to the airtight layer of the wall, for example to the internal plaster or, in timber construction, to the vapour barrier.

In renovation, the substrate is the biggest challenge. Old reveals are uneven, crumbly or covered with remains of foam and sealants. Before tapes can stick, these remains must be removed and the surfaces repaired. Often the joint is of uneven width; then the tapes must be chosen so that they work across the whole range, or the joint is evened out. If the exterior is to be insulated later, the outer seal should be chosen so that the insulation can be connected cleanly.

Who is responsible?

In practice, several trades often work at the joint: window fabricator, plasterer, painter and, in new builds, the drylining contractor. Clarify in advance who carries out which layer and who is responsible for the interfaces. Unclear responsibilities are a frequent cause of gaps in the sealing.

The lower connection: the window sill

The lower connection deserves particular attention because water stands and runs off here. The water must be led outwards over the external sill without getting under the frame. That takes a connecting profile under the frame, a seal between sill and frame and upstand profiles at the sides. For floor-to-ceiling elements and thresholds, additional rules of structural waterproofing apply. Suitable profiles are explained in the article on sill connecting profiles.

Checking airtightness

Whether the inner layer is tight can be demonstrated with an airtightness test. In a differential pressure test, leaks at the window connection become visible with smoke or air-speed measurement. In a new build, such a test is often part of quality assurance; in renovation it can make sense if draughts or moisture occur.

Checklist for the sealing

  • Fix the sealing system before installation: membranes, tapes or multifunctional tape
  • Check the joint width and choose a suitable tape
  • Prepare the substrate: clean, sound, level
  • Seal the inside all round without gaps, especially in the corners
  • Insulate the joint completely, foam only in the middle
  • Finish the outside driving-rain-tight and vapour-open
  • Execute the sill connection carefully
  • Photograph before plastering

The overarching framework for professional installation is described in the article on RAL installation. You can put windows and matching connecting profiles together in the configurator.

Frequently asked questions

What does tighter inside than outside mean for window installation?

The inner seal of the joint must be more vapour-tight than the outer one. That way moist room air cannot get into the joint, and any moisture that does get in can dry outwards. The other way round, moisture would build up in the joint.

Is expanding foam enough to seal a window?

No. PU foam fills and insulates the middle layer. But it is neither reliably airtight nor driving-rain-tight. Inside and outside, sealing tapes, membranes or sealants are also needed.

Which materials belong in which layer?

Inside, vapour-retarding, airtight membranes or tapes; in the middle, insulation such as PU foam or mineral wool; outside, driving-rain-tight, vapour-open tapes such as compressible tapes to DIN 18542 or external membranes. There are also multifunctional tapes that cover several layers.

How do I recognise faulty sealing?

Signs are draughts at the frame, moisture or mould at the reveal, water stains below the window or cracks in the render along the frame. If in doubt, a specialist firm should check the joint.

Sources

  1. dbfenster – Innen dichter als außen: Die drei Ebenen der Anschlussfuge(opens in a new tab)
  2. ift Rosenheim – Update Montageleitfaden Fenster und Außentüren(opens in a new tab)
  3. clean-invoice Wissen – RAL-Montage Fenster: Grundlagen und 3-Ebenen-Modell(opens in a new tab)
  4. Wikipedia – Wärmebrücke (DIN 4108-2)(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: RAL Window Installation: Professional Fitting
Shutters, security & installation

RAL Window Installation: Professional Fitting

RAL window installation explained: what the RAL and ift Rosenheim guideline covers, plus fixing, load transfer and sealing of the installation joint.

7 minutes read

Cover image: Fitting Windows Yourself: Possibilities and Limits
Shutters, security & installation

Fitting Windows Yourself: Possibilities and Limits

Fitting windows yourself: what skilled DIYers can manage, where the limits are, what applies to funding, tax bonus and warranty, with working steps.

7 minutes read

Cover image: Mushroom-Head Locking: How Hardware Stops Burglars
Shutters, security & installation

Mushroom-Head Locking: How Hardware Stops Burglars

Mushroom-head locking on windows: how mushroom cams and security keeps prevent levering, how they differ from roller cams, retrofitting and care.

6 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy