Configuring a Front Door Online: The Checklist for an Error-Free Order
7 minutes read
In the front door configurator you put your door together to measure step by step: dimensions, opening direction, model, material, security, insulation, colour, glass and accessories. To get the order right, clarify the technical basics beforehand, above all the survey, the funding conditions and the resistance class you want. This checklist takes you through all the points in the right order. The funding, withdrawal-right and energy rules mentioned refer to Germany; if you are elsewhere, check your own local rules.
Before the Configurator: What You Should Clarify
A configurator is quick to use, but the decisions behind it need preparation:
- Survey: exact dimensions of the wall opening and of the outer frame size you want, measured in several places. Instructions in the article on front door dimensions.
- Floor heights: where are the finished floors inside and outside? This determines threshold and door height.
- Funding: do you want to use the BEG grant or the tax bonus? Then the door needs 1.3 W/(m²K) at most, and with BAFA the application must be made before the order is placed (as at September 2026). Details in the article on front door grants.
- Fitting: who will fit it? For funding and the tax bonus, a specialist company is mandatory.
- Permissions: for heritage protection, design bylaws or flats under separate ownership, obtain consent beforehand.
Front Door Configurator: The Steps at a Glance
| Step | Decision | What to look for |
|---|---|---|
| 1. Dimensions | width × height, sidelights and fanlight if any | enter outer frame size, not structural opening size, if so required |
| 2. Opening | inward/outward, DIN left/right | mind the viewing direction |
| 3. Material and system | aluminium or uPVC | stability, colour, budget |
| 4. Model and infill | motif, inset or leaf-covering | U_D value of the motif |
| 5. Security | locking, resistance class, hardware | RC2 as the police recommendation |
| 6. Colour and finish | outside and inside separately | mind location and sun |
| 7. Glass | privacy, safety glass | matched to the resistance class |
| 8. Handle and accessories | pull handle, access, letterbox | power for motor lock |
| 9. Threshold | standard or low-barrier | water protection in front of the door |
| 10. Check and order | summary | check everything twice |
Step by Step: What Matters
1. Entering Dimensions
Enter exactly the dimension the configurator asks for, usually the outer dimension of the outer frame. Do not confuse it with the structural opening size or the clear passage size. If you are planning sidelights or a fanlight, decide the division beforehand; see front doors with sidelight and fanlight.
2. Opening Direction and Hand
Opening inwards or outwards? DIN left or DIN right? What counts is the view from the side towards which the door opens. A wrong DIN hand is one of the most common ordering mistakes. More in the article on front door opening direction.
3. Material
Aluminium offers stability for large formats and almost any colour, while uPVC scores with good insulation and a lower price.
4. Model and Infill
Choose the motif and the infill type. Leaf-covering infills give a smooth look and often insulate better. Check the U_D value for your motif, since glazed cut-outs tend to raise it.
5. Security
The German police crime-prevention service recommends at least resistance class RC2 to DIN EN 1627 for entrance doors. Also look for:
- multipoint locking with hook or pivot bolts,
- security escutcheon to DIN 18257,
- cylinder that finishes flush on the outside,
- automatic locking where appropriate.
6. Colour and Finish
Outside and inside can be finished differently. With dark colours on sunlit, unprotected sides, heed the manufacturer's guidance.
7. Glass
Privacy through satin-finish or patterned glass, security through laminated safety glass matched to the resistance class (P4A for RC2).
8. Handle, Access and Accessories
Pull handle or bar handle outside, lever inside. Fingerprint reader, motor lock or letterbox in the sidelight must be chosen now, since retrofitting is involved. Plan the power supply before fitting.
9. Threshold
For accessible entrances, 2 cm at most under DIN 18040-2. The lower the threshold, the more important canopy, fall and channel in front of the door become.
10. Check the Summary
Before you order, check every item in the summary. For made-to-measure goods, the statutory right of withdrawal under § 312g (2) no. 1 of the German Civil Code (BGB) is generally excluded, because the goods are not prefabricated and are made to your individual selection. Mistakes can hardly be corrected after ordering. If you are outside Germany, check the consumer rules that apply to you.
The Most Common Mistakes When Ordering Online
- Structural opening size entered instead of frame size: the door does not fit the opening.
- DIN hand swapped: the door swings to the wrong side.
- Floor build-up forgotten: threshold too high or too low.
- Funding application forgotten: grant lost.
- Accessories forgotten: motor lock or letterbox missing, and retrofitting is expensive.
- Colour chosen on screen only: samples on site give certainty.
Special Cases You Had Better Clarify Beforehand
Not everything can be reliably represented in a standard configurator. Agree the following cases with the supplier before ordering:
- Special shapes such as round arches, slopes or very tall fanlights,
- Extra-wide or extra-tall doors outside the system limits,
- Fire or smoke protection requirements, for example for doors between garage and house,
- Heritage protection conditions with requirements on material and division,
- Integration into building technology such as access control, alarm system or smart home,
- Contract projects with several doors or blocks of flats.
In these cases a short exchange with the supplier helps before you place a binding order.
For Trade Businesses
Window fitters, joiners and building firms who order front doors regularly benefit from fixed routines: uniform survey sheets, standardised terms for hand and installation situation, and a second check of every configuration by a colleague. This markedly reduces incorrect orders.
After the Order
- Check the order confirmation carefully for every item and report deviations immediately.
- Agree the delivery date with the fitting firm.
- Complete power connections and preparations on site.
- On delivery, check packaging and door for transport damage and document it immediately.
- After fitting, hold the handover with a function check and obtain the documents for funding.
Discuss the Configuration Before Ordering
Keep a written record of your configuration, for example a screenshot of the summary or a list of all the options chosen. That way you can discuss it with the fitting firm, the energy efficiency expert or, in blocks of flats, the managing agent before you order. The expert can use the technical data to check whether the door meets the funding requirements, and the fitter can see early whether the installation situation and threshold fit together.
The Printable Checklist
- Survey in several places, outer frame size determined
- Floor heights inside and outside established
- Opening direction and hand noted with a sketch
- Funding clarified, BAFA application made before the order
- Material, model, infill chosen
- Resistance class and locking decided
- U_D value checked for the specification (≤ 1.3 W/(m²K) for funding, legally ≤ 1.8 W/(m²K))
- Colour outside/inside, glass, handle, accessories chosen
- Threshold suited to use and water protection
- Summary and order confirmation checked
- Fitting by a specialist firm organised
With this list you are ready: start now in the configurator or first get an overview of the front doors.
Frequently asked questions
What information do I need for the front door configurator?
At least the exact dimensions of the opening or the outer frame size, the opening direction and hand, the material and model you want, the colour outside and inside, and your requirements for security and thermal insulation.
Can I return a made-to-measure front door?
For goods made to the customer's specification, the statutory right of withdrawal under German law is generally excluded. Check your configuration with particular care before you order.
Must I apply for funding before ordering?
For BEG funding via BAFA, yes: the application must have been made before you place a binding order. For the tax bonus under § 35c EStG no advance application is needed, but the door must meet the technical requirements and be fitted by a specialist firm.
What if I am unsure about my survey?
Have the survey done by a specialist firm or clarify your dimensions with the supplier before ordering. A measuring error is the most common and costliest mistake with made-to-measure orders.
Sources
- BAFA – Einzelmaßnahmen an der Gebäudehülle(opens in a new tab)
- § 312g BGB – Widerrufsrecht (Ausschluss bei Kundenspezifikation)(opens in a new tab)
- Polizeiliche Kriminalprävention – Haus- und Wohnungstür sicher machen(opens in a new tab)
- Gebäudemodernisierungsgesetz (GModG), Anlage 7(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.