Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Energy & grants

Heat Pump and Windows: Why the Building Envelope Decides the Efficiency

6 minutes read

A heat pump works more efficiently the lower its flow temperature can be, and that depends directly on the building envelope. New, tightly fitted windows reduce the heat load and make lower flow temperatures possible. Replacing windows is not a requirement before installing a heat pump, but very old, leaky windows cost electricity permanently and should be considered in the planning.

Heat pumps have long since arrived in existing homes: according to dena, the German Energy Agency, around 194,500 heat pumps were sold in Germany in the first half of 2026, 40 per cent more than in the same period of the previous year. That makes the question of how heating and building envelope work together all the more important. Funding details below refer to Germany; if your property is elsewhere, please check local incentives and rules.

Heat pump and windows: the physical connection

A heat pump lifts ambient heat to the temperature level that the radiators or underfloor heating need. The greater the temperature lift, the more electricity it uses. Two quantities decide:

  • Heat load: the heating output needed on a very cold day to keep the house warm. It results from transmission losses through walls, roof, floor and windows, as well as from ventilation losses.
  • Flow temperature: the temperature at which the heating water flows into the heat emitters. It has to be higher the greater the heat load is in relation to the emitter area.

New windows reduce both kinds of loss: a Uw-value of 0.95 W/(m²K) instead of an old double-glazed window cuts heat conduction markedly, and airtight installation prevents uncontrolled air changes. The portal 42watt describes the effect like this: leaky building envelopes force heat pumps to run at higher flow temperatures, which lowers the seasonal performance factor. Every kelvin less of flow temperature saves roughly 2.5 to 3 per cent of electricity.

Where windows make the most difference

Large glass areas and old glazing

Houses with many windows, large patio doors or conservatory extensions lose a large share of their heat through the glass. Here a replacement has a disproportionate effect. How to estimate the saving yourself is shown in the article Saving heating costs with new windows.

Rooms with a high heat load

Often individual rooms decide the flow temperature required: a corner room with two external walls and large windows, a bathroom with a high target temperature or a living room with a panoramic window. If exactly these rooms get better windows, the flow temperature for the whole house can fall.

Cold surfaces and comfort

Old windows have cold glass surfaces on the inside. This causes cold downdraughts and the feeling of a draught, even if the window is airtight. With a heat pump and low flow temperatures, the heat emitters are less hot, so the cold air curtain at the window is felt more strongly. Modern triple glazing with a warm edge has much warmer inner surfaces. Details in the article Warm edge: spacers and condensation.

Planning the right order

The order of measures is one of the most important planning questions in an existing building:

Situation Recommendation
Windows are old, replacement planned within the next few years Have the heat load calculated for the state after the window replacement and size the heat pump accordingly
Windows are relatively new, heating has failed Install the heat pump now, envelope measures later step by step
Comprehensive refurbishment planned Draw up a renovation roadmap with an energy consultant and coordinate envelope and heating

If the heat pump is sized for an unrefurbished house and windows, roof and façade are improved afterwards, it may be oversized. That leads to frequent cycling and poorer efficiency. An individual renovation roadmap helps put the steps in order; more in the article Energy efficiency expert and iSFP, and on the sequence of measures in Refurbishing an existing building: order of windows, façade, roof.

A test in your existing home: how low can the flow temperature go today?

Before you decide on windows and a heat pump, a simple experiment with your existing heating is worthwhile. During the heating season, lower the heating curve of your boiler step by step and watch whether all rooms still get warm. Note the outdoor temperature and the room that becomes too cold first. This tells you

  • which flow temperature your house actually needs at present,
  • which rooms determine the sizing,
  • whether windows, radiator size or an uninsulated wall are the cause there.

If a room with large, old windows is the bottleneck, a targeted window replacement or a larger radiator in exactly that room can achieve more than a measure across the whole house. The results are also a valuable basis for the heating installer and the energy consultant. The experiment does not replace a professional heat load calculation, however.

Roller shutters as a complement

Closed roller shutters further reduce heat loss through the window at night, provided the shutter box itself is well insulated and airtight. An old, uninsulated box, on the other hand, can be the biggest weak point of the window opening. More in the article Insulating roller shutter boxes.

Do not forget airtightness and ventilation

New windows make the house more airtight. That is wanted in energy terms, but it changes the moisture balance: leaky joints used to provide an uncontrolled air change, whereas now you have to ventilate deliberately. When more than a third of the windows in a one- or multi-family house are replaced, the German standard DIN 1946-6 calls for a ventilation concept. What that looks like is explained in the article Ventilation concept under DIN 1946-6.

The German Federal Environment Agency also recommends heating all rooms sufficiently and not covering radiators with casings, oversized window cills or heavy curtains, which matters all the more with the lower surface temperatures of a heat pump system.

Funding for windows and heat pumps

In Germany, windows and heating are funded separately:

  • Windows: BAFA grant through the BEG individual measures, 15 % of eligible costs, Uw ≤ 0.95 W/(m²K); since 21 July 2026 the iSFP bonus applies only to the share of costs above €30,000 (as of September 2026).
  • Heat pump: KfW heating funding. KfW adjusted the conditions on 21 July 2026; you will find details directly at KfW.

Alternatively, owner-occupiers can consider the tax bonus under § 35c of the German Income Tax Act (EStG) for the windows. An overview of the routes is given in the article KfW or BAFA for windows?. Funding conditions change; this article does not replace funding advice.

Common misunderstandings

  • "With a heat pump, you no longer need good windows." The heat pump makes heat efficiently, but not free of charge. Every kilowatt hour lost through old windows has to be generated with electricity.
  • "The house has to be fully insulated first." Many existing buildings can sensibly be heated with a heat pump even without a full refurbishment. What matters is a realistic heat load calculation and, where necessary, replacing individual radiators.
  • "Triple glazing only pays off in a passive house." Especially at low flow temperatures, warm glass surfaces noticeably improve comfort.

Checklist: thinking windows and heat pump together

  1. Record the condition and age of the windows, especially in rooms with a high heat load.
  2. Commission a room-by-room heat load calculation, for the current state and for the state after planned envelope measures.
  3. Agree the order and timetable with an energy consultant.
  4. Have new windows installed airtight and with minimal thermal bridges.
  5. Check the ventilation concept under DIN 1946-6.
  6. Submit funding applications before placing orders.

If you want to replace your windows as part of a heating modernisation, put together eligible windows with suitable glazing in the window configurator. If you have questions about the selection, our team can help you via the contact page.

Frequently asked questions

Do I have to replace my windows before installing a heat pump?

Not necessarily. Many existing buildings can be heated with a heat pump without a full refurbishment. Very old, leaky windows do raise heat load and flow temperature, however, and so reduce efficiency.

Why is the flow temperature so important?

The lower the flow temperature, the less electricity the heat pump needs for the same amount of heat. The portal 42watt puts the saving at roughly 2.5 to 3 per cent less electricity consumption for every kelvin of lower flow temperature.

What is the right order: windows first or heat pump first?

Ideally, the heat load is calculated for the state after the planned envelope measures. If you will be replacing windows in the next few years anyway, allow for this in the sizing so that the heat pump is not oversized.

Are windows and heat pumps funded separately?

Yes. In Germany, windows are funded as an individual measure through the BEG at BAFA, and the heating through KfW heating funding. The conditions were adjusted on 21 July 2026; check the current position before applying.

Sources

  1. 42watt: Blower-Door-Test – Luftdichtheit für Wärmepumpen prüfen(opens in a new tab)
  2. dena: Wärmepumpe und Batteriespeicher geben Impulse für die Gebäudewende(opens in a new tab)
  3. KfW Pressemitteilung: Anpassungen in den KfW-Produkten der BEG (08.07.2026)(opens in a new tab)
  4. BAFA – Gebäudehülle (BEG EM)(opens in a new tab)
  5. Umweltbundesamt: Richtig heizen, Schimmelbildung vermeiden(opens in a new tab)
  6. Energie-Fachberater: Lüftungskonzept beim Fenstertausch(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Condensation on Windows: Causes and Solutions
Energy & grants

Condensation on Windows: Causes and Solutions

Condensation on windows inside, outside or between the panes: what causes it, when it is harmless and what really helps against misted-up windows.

6 minutes read

Cover image: Energy Certificate Germany: How New Windows Count
Energy & grants

Energy Certificate Germany: How New Windows Count

German energy certificate (Energieausweis) and windows: how new windows enter demand and consumption certificates, what classes A+ to H mean and when to reissue

6 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy