Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Energy & grants

Condensation on Windows: Why Panes Mist Up and What Really Helps

6 minutes read

Condensation on windows forms when humid room air cools on a surface that is colder than its dew point. Indoors, the cause is almost always too much humidity combined with a cold glass or frame edge. Panes that mist up on the outside, by contrast, are a sign of very good insulation, and moisture between the panes points to a failed sealed unit.

The solution therefore depends on where the water sits. This article helps with the diagnosis and shows what actually works. The humidity and ventilation guidance comes from the German Federal Environment Agency; the principles apply anywhere, but for local rules and recommendations please check your own country's guidance.

How condensation forms on windows

Warm air can hold more water vapour than cold air. When air cools on a cold surface, its relative humidity rises until water condenses at the dew point. On a window, the coldest places are usually:

  • the glass edge, where the spacer joins the panes,
  • the lower edge of the pane, because cold air collects there,
  • the connection joint and reveal, if the installation has thermal bridges.

That is why misting almost always starts at the bottom glass edge and then creeps upwards.

The three places for condensation compared

Place Typical cause Assessment Action
Inside, on the pane high room humidity, cold glass surface warning sign if permanent ventilate, heat, reduce moisture sources, improve window or glass if necessary
Outside, on the pane excellent thermal insulation, clear cold nights not a defect none, usually disappears by late morning
Between the panes leaking edge seal of the sealed unit defect replace glass or window

Condensation on the inside of the window: causes

Humidity too high

The German Federal Environment Agency recommends a relative humidity between 40 and 60 per cent. Cooking, showering, drying laundry and house plants raise humidity, and so do people themselves: according to the agency, each person gives off roughly a quarter of a litre of water into the room air per night. That is why bedroom windows mist up particularly often.

Rooms that are too cold

Unheated or only occasionally heated rooms have cold surfaces. The agency advises keeping bedrooms at 16 °C or above at night and keeping doors to cooler rooms closed, so that humid warm air does not drift there and condense on cold surfaces.

Covered radiators and window recesses

Oversized window cills, radiator casings and heavy curtains stop warm air rising in front of the pane. The glass stays cold, which creates ideal conditions for condensation.

Old windows and cold glass edges

Older sealed units with aluminium spacers have a particularly cold glass edge. Modern glazing with a "warm edge" and triple glazing has much higher surface temperatures. More in the article Warm edge: spacers and condensation.

After replacing the windows

Many owners notice condensation only after new windows have been fitted, and in different places. The reason: the new windows are airtight, the uncontrolled air change through leaky joints disappears, and the moisture stays in the room. The window is no longer the coldest spot; instead, external-wall corners or reveals can become damp. How to prevent this is shown in the article Avoiding mould after window replacement.

What helps against misted windows inside

  1. Purge ventilation instead of tilting: In the cold season, the Federal Environment Agency recommends two to three times a day, about five minutes per room, with the window wide open. Permanently tilted windows cool walls and reveals.
  2. Ventilate away moisture sources directly: In the kitchen and bathroom, ventilate during and straight after cooking or showering.
  3. Put up a hygrometer: Only if you know the humidity can you react sensibly.
  4. Heat all rooms: Do not let even rarely used rooms cool right down.
  5. Keep radiators clear: Place curtains and furniture so that warm air can circulate in front of the window.
  6. Wipe off condensation: Do not leave water standing on frames and seals, so that no mould forms.
  7. Check the ventilation concept: If you cannot ventilate during the day, you need ventilation that does not depend on the occupants, for example trickle vents or a ventilation system. See Ventilation concept under DIN 1946-6.

Condensation outside: no cause for concern

Outer panes that are misted in the morning occur mainly with triple glazing with a very low Ug-value. Because hardly any heat escapes from the room to the outside, the outer pane cools strongly on clear, windless nights, much like a car roof. The condensation disappears as soon as the sun warms the pane. It is proof of good insulation and no reason for a complaint.

Moisture between the panes

If the glass is misted in the cavity between the panes, neither ventilating nor wiping helps. The edge seal has failed, moisture has got in and the desiccant in the spacer is saturated. The unit has to be replaced. How to recognise the problem, and whether a glass replacement or a new window is worthwhile, is described in the article Misted pane between the glass.

Special cases: bathroom, kitchen, roof windows and conservatories

Bathrooms and kitchens produce a lot of moisture in a short time. Windows here mist up regularly; what matters is that they dry off again quickly after showering or cooking. Open the bathroom window wide straight after showering and keep the bathroom door closed so that the steam does not drift into the home.

Roof windows are inclined and, because of their installation position, have a colder glass surface than vertical windows of the same quality. In addition, warm, humid air rises. Condensation on roof windows is therefore more common, which makes good glazing and regular ventilation all the more important. More on the differences in the article Roof windows vs vertical windows.

Conservatories and large glazed fronts cool strongly at night. Without sufficient heating and ventilation, the panes mist up over large areas. Even basic background heating and an air flow that keeps humid air away from the glass help here.

New builds release a lot of construction moisture from screed, plaster and masonry in the first months. Misted windows in the first winter are therefore common; intensive ventilation and even heating dry the building out.

When to call in a specialist firm

  • Condensation occurs daily despite correct ventilation.
  • Frame, reveal or window board show mildew spots or mould.
  • The reveal is distinctly colder than the wall next to it, which points to a thermal bridge at the connection.
  • The window is misted up between the panes.

For thermal bridges at the connection, professional installation to the state of the art helps. The basics are explained in the article Avoiding thermal bridges at the window connection.

One last note: dehumidifiers or salt-granule containers only treat symptoms. In individual cases, for example while a building is drying out, they can help, but they replace neither proper ventilation nor professional rectification of thermal bridges.

Checklist

  1. Determine the location of the condensation: inside, outside or in between.
  2. Measure the humidity, target range 40 to 60 per cent.
  3. Adjust your ventilating and heating habits.
  4. Keep radiators and window recesses clear.
  5. If the edge seal has failed, replace the glass or window.
  6. For old windows with cold glass edges, consider new glazing.

If your windows are permanently misted on the inside and the glazing is outdated, it is worth looking at modern triple glazing with a warm edge. In our windows overview you will find profiles and glazing for new builds and refurbishments.

Frequently asked questions

Is condensation on the inside of a window normal?

Occasionally, for example in the morning in a bedroom or after a shower, it is not unusual. If it occurs daily and over large areas, the humidity is too high or the glass surface too cold, and there is a risk of mould on the frame and in the reveal.

Why do new windows mist up on the outside?

External condensation occurs because very well-insulating glazing gives off hardly any heat to the outside. On clear nights the outer pane cools below the dew point of the outside air. It is a sign of good insulation and not a defect.

What relative humidity is right in living spaces?

The German Federal Environment Agency (Umweltbundesamt) recommends a relative humidity between 40 and 60 per cent. A simple hygrometer helps you keep an eye on the value.

What should I do if the window is misted up between the panes?

Then the edge seal of the sealed unit has failed. Ventilating does not help here; the glass unit or the window has to be replaced.

Sources

  1. Umweltbundesamt: Richtig lüften, Schimmelbildung vermeiden(opens in a new tab)
  2. Umweltbundesamt: Richtig heizen, Schimmelbildung vermeiden(opens in a new tab)
  3. Umweltbundesamt: Schimmel – Überblick(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Misted Double Glazing Between the Panes: What to Do
Energy & grants

Misted Double Glazing Between the Panes: What to Do

Pane misted between the glass? How to recognise a failed edge seal, why wiping does not help and when a glass replacement or a new window is worthwhile.

6 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy