Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Lift-and-slide doors

Large glass areas: what weight, structure and glass thickness mean for your window planning

7 minutes read

Large glass areas in windows and sliding doors bring a lot of light into the house, but also a lot of weight. Glass weighs around 2.5 kg per square metre per millimetre of thickness; triple glazing with three 4 mm panes therefore comes to about 30 kg/m². What glass thickness a large pane needs is calculated by the manufacturer to DIN 18008, and hardware, frame and building must carry the load safely. DIN 18008 is the German glass design standard; in the UK, the equivalent design is normally done to BS 6262 and the relevant Eurocodes, so check with your supplier.

How to calculate glass weight

Float glass has a density of around 2.5 g/cm³, i.e. 2,500 kg/m³. That gives a simple rule of thumb:

Glass weight in kg/m² ≈ sum of all pane thicknesses in mm × 2.5

Gas fill and spacers hardly add to the weight. Some examples:

Build-up Total glass thickness Weight per m² (approx.)
Double 4/16/4 8 mm 20 kg
Triple 4/12/4/12/4 12 mm 30 kg
Triple 6/14/4/14/6 16 mm 40 kg
Triple with 8 mm laminated safety glass inside and 6 mm outside 18 mm 45 kg

For comparison: a sliding sash with 2.5 m × 2.4 m of glass has 6 m² of glass. At 30 kg/m², the glazing alone weighs around 180 kg, and at 45 kg/m² already 270 kg, before adding the sash frame and reinforcement.

Why large panes need thicker glass

A pane of glass is stressed by several loads:

  • Wind load: pressure and suction act on the entire surface. The larger the pane, the more it deflects.
  • Climatic load: a fixed volume of gas is enclosed in the cavity of an insulating glass unit. If temperature or air pressure changes, the gas expands or contracts and the panes bulge.
  • Self-weight: with sloping and overhead glazing, the weight also acts on the pane.
  • Impact: in areas where people could fall against the glass, glass with safe breakage behaviour is needed.

To limit deflection and stresses in the glass, the manufacturer chooses thicker individual panes for large formats, often 6 or 8 mm instead of 4 mm. That adds further weight.

The reverse effect with small panes is interesting: narrow, short insulating glass units are very stiff and build up particularly high stresses under climatic loads. Technical sources therefore give minimum edge lengths of around 60 cm for triple glazing, and up to about 1 m for acoustic build-ups. A narrow fixed panel next to a large sliding door may therefore also need an adapted glass build-up.

DIN 18008: the rulebook for glass in construction

The DIN 18008 series of standards governs the design and construction of glass in buildings. According to the guide from the German Federal Association of Flat Glass (Bundesverband Flachglas), it consists of six parts:

  1. Part 1: terms and general principles
  2. Part 2: linearly supported glazing, which means classic windows and doors
  3. Part 3: point-supported glazing
  4. Part 4: additional requirements for glazing that protects against falls
  5. Part 5: additional requirements for walk-on glazing
  6. Part 6: additional requirements for glazing that can be stepped on for maintenance and is resistant to falling through

For large patio doors and panoramic windows, Part 4 is often relevant alongside Part 2: if the bottom edge is low and there is a risk of falling, for example on an upper floor, the glass itself must be designed as fall protection or a separate balustrade is needed. Laminated safety glass is normally used for this. When which safety glass is required is explained in the article toughened and laminated glass in windows.

For monolithic toughened safety glass in vertical glazing, the guide gives an installation height of at most 4 m; above that, other types of glass or heat-soaked toughened glass (ESG-H) are needed.

Size limits: glass, profile, hardware

How large a pane can be is decided at several points:

  • Glass production: float glass is produced in Europe in jumbo size 6,000 × 3,210 mm. Larger panes are special formats.
  • Profile system: manufacturers state maximum sash sizes. Schüco, for instance, quotes sashes up to 3,200 × 3,500 mm for its ASE 60 and ASE 80.HI aluminium lift-and-slide systems and up to 2,465 × 2,468 mm for the LivIngSlide uPVC system.
  • Hardware: lift-and-slide hardware is graded by sash weight. The Siegenia PORTAL HS goes up to 400 kg of sash weight and spreads the load across eight rollers in this class.
  • Transport and installation: above a certain size, special vehicles, cranes or vacuum lifters are needed. More in the article on transporting and delivering large glass elements.

What the structural engineer should check on the building

It is not only the element itself that has to carry the load, but also the structure:

  • Lintel: over large openings, the lintel must be sized so that it does not deflect onto the element. Lift-and-slide doors are sensitive to deflection because otherwise the sashes no longer move easily.
  • Threshold bearing: the threshold carries the entire sash weight. It must be supported continuously, not just at points.
  • Fixing: the number and type of fixings depend on element size and wind load. Where there is insulation in front of the wall, mounting systems with tested load capacity are used.
  • Building movement: large elements need joints that absorb movement of the structure without glass or frame being subjected to constraint forces.

For new builds with very large glazed areas, the structural engineer should plan the connections from the start.

Storage and handling on site

Large insulating glass units are sensitive before they are installed. The guideline of the Federal Association of Flat Glass on handling multi-pane insulating glass sets out clear rules:

  • Store vertically only: insulating glass may only be stood in a vertical position on suitable racks, never flat.
  • Protect from the weather: units stored outdoors must be fully covered against prolonged moisture and sunshine.
  • Limit deflection: the edge seal may deform perpendicular to the pane at one edge by no more than 1/200 of the edge length, at most 15 mm.
  • Check before installation: every delivered glass unit must be checked for damage before installation.

The same principles apply by analogy to finished door and window elements with glass fitted. Plan a dry, level storage area near the installation point.

Energy and comfort

Large glass areas also influence the indoor climate. In winter they provide solar gains, in summer they can lead to overheating. So plan solar shading from the outset, either external or via solar-control glass. Background is given in the article avoiding overheating with glass fronts. As for the glazing itself, triple glazing with a warm-edge spacer gives high inside surface temperatures, so there is no unpleasant cold radiation even right next to the pane.

Checklist for planning large glass areas

  • Calculate the glass weight roughly and compare it with the hardware class
  • Have the manufacturer size the glass thickness and type to DIN 18008
  • Clarify fall protection if the bottom edge is low
  • Agree lintel, threshold bearing and fixing with the planner
  • Arrange delivery, crane or vacuum lifter in good time
  • Think about solar shading and cleaning the outside

Are you planning a large glass front? Our range includes lift-and-slide doors in uPVC and aluminium. In the configurator you can see the permissible glazing for your dimensions and get an instant price; for special formats we are happy to prepare an individual quotation.

Frequently asked questions

How heavy is one square metre of triple glazing?

Glass has a density of around 2.5 g/cm³, so roughly 2.5 kg per square metre per millimetre of glass thickness. Triple glazing made of three 4 mm panes therefore weighs around 30 kg/m²; with thicker panes or laminated glass, correspondingly more.

Who determines the glass thickness for large panes?

The window or glass manufacturer sizes the glass thickness to DIN 18008. Pane size, wind and climatic loads, installation height and how the pane is supported all feed into this.

How large can a single pane of glass be?

In Europe, float glass is produced as standard in jumbo size 6,000 × 3,210 mm. Larger panes are special orders; in practice, the profile system, hardware, transport and installation usually limit the size sooner.

Why are small, narrow insulating glass units more prone to breakage?

Insulating glass deforms with changes in temperature and air pressure. Small, narrow panes are stiffer and build up higher stresses as a result. Technical sources therefore recommend minimum edge lengths of around 60 cm for triple glazing.

Sources

  1. Floatglas – Wikipedia (Dichte, Standarddicken, Bandmaß)(opens in a new tab)
  2. Isolierglas – Wikipedia (Gewicht, Gasfüllungen, Klimalast)(opens in a new tab)
  3. BF-Merkblatt 019 – Leitfaden zur Glasbemessung nach DIN 18008(opens in a new tab)
  4. BF-Merkblatt 002 – Richtlinie zum Umgang mit Mehrscheiben-Isolierglas(opens in a new tab)
  5. SIEGENIA PORTAL HS 400 kg – Hebe-Schiebe-Beschlag(opens in a new tab)
  6. Schüco Schiebetüren – maximale Flügel- und Elementmaße(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Zero Threshold Waterproofing: Draining Water Safely
Lift-and-slide doors

Zero Threshold Waterproofing: Draining Water Safely

Zero threshold at a patio or balcony door: how waterproofing, drainage channel and falls work, what the German flat-roof guideline requires and what to avoid.

6 minutes read

Cover image: Panoramic Windows and Fixed Glazing: Planning Guide
Lift-and-slide doors

Panoramic Windows and Fixed Glazing: Planning Guide

Panoramic windows and fixed glazing: benefits, limits, fall protection, energy values and cleaning, so you can plan large windows with a view properly.

6 minutes read

Cover image: Level-Access Patio Door: Planning Step-Free Entry
Lift-and-slide doors

Level-Access Patio Door: Planning Step-Free Entry

Planning a level-access patio door: what DIN 18040-2 says on thresholds and clear widths, which door systems suit, and how to keep the transition watertight.

6 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy