Configure a lift-and-slide door online: how to measure correctly and order with confidence
6 minutes read
You can configure a lift-and-slide door online successfully if you get three things right: measure the wall opening carefully, derive the correct order size from it, and choose scheme, threshold, glazing and colour to suit your installation situation. Because made-to-measure elements are generally exempt from the right of withdrawal, it is worth checking every dimension twice, or for large elements commissioning a survey by the installation firm.
Step 1: measure the opening correctly
What you need
- A folding rule or tape measure (for large openings, a laser distance meter is better)
- A spirit level
- A notepad or smartphone for a sketch and photos
How to measure
- Width at three points: at the top under the lintel, in the middle and at the bottom above the floor. Note the smallest dimension.
- Height at three points: left, middle, right, each from the structural floor or the future bearing surface of the threshold up to the lintel. Here too the smallest dimension counts.
- Diagonals: measure both diagonals. If they differ considerably, the opening is not square.
- Check the floor: lay the spirit level on the floor of the opening. A lift-and-slide door needs an exactly level bearing surface; any fall must be compensated for later.
- Check the rebate: does the opening have a masonry or plaster rebate? Then also measure the clear dimension between the rebates.
When replacing
If an old door is being replaced, do not just measure the old frame. The real dimension is the wall opening behind it. If possible, remove some silicone or a cover strip on the inside to see the joint, or have the survey checked after removal. General tips for all windows are in the article measuring windows correctly.
Step 2: from opening size to order size
The element must be smaller than the opening so that there is room all round for fixing, insulation and sealing. The required installation joint depends on element size, material and type of connection and is specified by the manufacturer. With large elements and aluminium, which has higher thermal expansion, the joints are often wider.
The height matters too: depending on the system, lift-and-slide thresholds are placed on the structural floor and packed, or recessed into the screed. The element height therefore depends on where the top of the future finished floor will be and how the threshold is connected. Clarify this before ordering.
| Term | Meaning |
|---|---|
| Wall opening / structural size | opening in the masonry without plaster |
| Clear size | distance between rebates or reveals |
| Element size / order size | outside dimension of the frame |
| Installation joint | gap between frame and masonry |
| Clear passage width | width actually free to walk through with the sash open |
Step 3: choose scheme and sliding direction
In the configurator you choose how the front is divided, for example one sliding sash with a fixed panel (scheme A) or two sliding sashes towards the centre with two fixed panels (scheme C). Decide on which side the sash runs. Make sure whether the drawing shows the view from inside or from outside. An overview of the variants is in the article HST schemes A, C, G and K.
Check the clear passage width at the same time: with scheme A it is considerably less than half the element width because frame, overlap and handle are deducted. For an accessible passage, DIN 18040-2 gives a clear width of at least 90 cm.
Step 4: threshold, glass and specification
- Threshold: standard or low for a near step-free transition. A low threshold requires suitable waterproofing and drainage.
- Glazing: double or triple glazing, possibly safety glass, solar-control or acoustic glass. The glazing determines weight and Uw value.
- Energy value: when replacing in residential buildings in Germany, Annex 7 GModG gives a maximum of Uw 1.6 W/(m²K) for door-windows with a sliding or lifting mechanism; for BAFA funding, Uw 0.95 W/(m²K) must generally be demonstrated (status: September 2026). For funding, the application must be submitted before the contract is awarded. These are German rules; readers in the UK or elsewhere should check their own building regulations.
- Colour: the same inside and outside or different, for example anthracite outside, white inside.
- Security: burglar-resistant hardware, lockable handle, safety glass.
- Accessories: roller shutter, insect screen, drive, as available in the system.
Step 5: check plausibility
Before you order, go through the configuration once more:
- Do the dimensions match the smallest measured opening less the joint?
- Is the sliding sash on the correct side?
- Is the clear passage width sufficient?
- Does the threshold height suit the future floor?
- Are the colours inside and outside right?
- Can the element be transported and does it reach the installation point? See delivering large glass elements.
Measure yourself or commission a survey?
For a standard situation (straight opening, solid floor, clear floor build-up), you can take the measurements yourself if you work carefully. In the following cases we recommend a survey by the installation firm:
- Very large elements several metres wide or with heavy sashes
- Renovation with a new floor build-up, where the future floor height is not yet fixed
- Step-free transitions with channel and waterproofing
- Out-of-square or irregular openings in older buildings
- The opening is being enlarged, in which case it is a matter of structure and lintel anyway
Whoever takes the survey generally also bears responsibility for the element fitting. If your installation firm measures and orders, the risk of wrong dimensions lies with them.
Sketch and photos help
Make a simple sketch of each opening with all dimensions and photograph the opening from inside and outside. Mark sockets, radiators, light switches and furniture nearby. That lets you fix the sliding direction with confidence, and if the manufacturer has questions you have all the information to hand.
Typical mistakes when ordering online
- Taking over the frame size of the old door without checking the joint.
- Forgetting the finished floor: the threshold ends up too high or too low.
- Sliding direction mixed up: not noticing the view from inside and outside.
- Entering dimensions in centimetres instead of millimetres.
- Not realising that the opening is out of square: the element does not fit or only with large joints.
Legal: made-to-measure goods and withdrawal
When buying online in Germany, consumers generally have a right of withdrawal. Under section 312g (2) no. 1 BGB, however, contracts for goods that are not prefabricated and for whose manufacture an individual choice or determination by the consumer is decisive, or that are clearly tailored to their personal needs, are exempt. A lift-and-slide door made to your dimensions generally falls under this. Details are explained in the article made-to-measure goods and the right of withdrawal. Consumer law differs between countries, so check your local rules. This note does not replace legal advice.
Configure now
In the configurator you enter your dimensions, choose scheme, threshold, glazing and colour and see the drawing and price immediately. You will find all systems on the lift-and-slide doors page. For window fitters and building firms we also offer a B2B account with tiered discounts.
Frequently asked questions
Which dimension do I enter in the configurator?
As a rule, the element size, that is, the outside dimensions of the frame. It is derived from the wall opening less the installation joint specified by the manufacturer. Check in the configurator whether it asks for element size or opening size.
How do I measure the opening for a lift-and-slide door?
Measure the width at the top, in the middle and at the bottom, and the height at the left, in the middle and at the right. Use the smallest dimension in each case and also check the diagonals to spot out-of-square openings.
Can I return a made-to-measure door?
In Germany, goods that are not prefabricated and whose manufacture depends on your individual choice are exempt from consumers' right of withdrawal under section 312g BGB. That is why precise measuring and checking before ordering matters so much; readers elsewhere should check local consumer law.
Should I have a specialist firm survey the opening?
For large lift-and-slide doors, out-of-square openings, renovations with a new floor build-up or step-free transitions, a survey by the installation firm is recommended. The firm is then also liable for the dimensions.
Sources
- nullbarriere.de – DIN 18040-2: Türen (lichte Breite und Höhe)(opens in a new tab)
- Anlage 7 GModG – Höchstwerte der Wärmedurchgangskoeffizienten(opens in a new tab)
- BAFA – Einzelmaßnahmen an der Gebäudehülle(opens in a new tab)
- § 312g BGB – Widerrufsrecht (Ausnahme für nicht vorgefertigte, individuell bestimmte Waren)(opens in a new tab)
- Schüco Schiebetüren – maximale Flügel- und Elementmaße(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.