Rebate trickle vents and window vents: fresh air without much heat loss
6 minutes read
A rebate trickle vent is a small component, invisible from outside, in the rebate between sash and frame, which allows a slight, constant air exchange when the window is closed. It is mainly suited to supporting the user-independent ventilation for moisture protection under DIN 1946-6, not to replacing airing in short bursts. Its airflow lies, depending on model and wind pressure, in the range of a few cubic metres per hour. DIN 1946-6 is a German standard; in the UK, the equivalent question is answered by Approved Document F and the trickle vents your installer specifies, which are usually fitted in the frame head.
When replacing windows in an existing building, it is often the simplest answer if the ventilation concept finds a small additional need.
How a rebate trickle vent works
Modern windows have two or three all-round sealing planes. A rebate vent is fitted in the upper part of the sash; at this point the stop seal and centre seal are cut away over a short length. This creates a defined air path through the rebate even though the window is closed and locked.
The air movement is driven purely by natural pressure differences:
- Wind creates overpressure on the windward side and underpressure on the leeward side.
- Stack effect arises because warm indoor air is lighter than cold outdoor air.
So that too much cold air does not flow in during a storm, many rebate vents have a pressure-controlled flap. It partly closes as the pressure difference rises and limits the volume flow.
Airflow: a practical example
Manufacturers state the volume flow at defined pressure differences. For the Siegenia AEROMAT mini, the installation instructions give the following values:
| Pressure difference | Airflow (approx.) |
|---|---|
| 4 Pa | 3 m³/h |
| 8 Pa | 5 m³/h |
| 10 Pa | 6 m³/h |
| 100 Pa | up to 14 m³/h |
According to Siegenia, the manufacturer's figure for 10 Pa refers to installation in pairs. For comparison: larger, visible window vents from the same manufacturer, such as the AEROMAT midi, reach about 30 m³/h at 10 Pa.
The figures show the order of magnitude. A rebate vent delivers a small, steady quantity of air, which is exactly what is often missing for moisture protection once new windows have removed the old leaks. For normal living, this quantity is not enough.
When a rebate vent is the right choice
Whether a rebate vent is enough is decided by the ventilation concept under DIN 1946-6. Typical cases in which it fits well:
- Window replacement in a single-family house, where the calculation shows only a small shortfall for moisture protection
- Flats with no room for ducts, where a ventilation system is out of the question
- Bedrooms, where a small basic air change is wanted at night
- Rented flats, where moisture protection should not depend on the tenants' ventilation behaviour
It is less suitable where a high air change is needed, for example in internal bathrooms without a window, or where the building is very airtight and has many occupants. The concept then usually plans an extract system or units with heat recovery. You will find the overview of the options in the article on the ventilation concept for window replacement.
Advantages and disadvantages at a glance
| Advantages | Disadvantages |
|---|---|
| barely visible from outside and inside | only small air quantities |
| no power supply needed | depends on wind and stack effect |
| no maintenance of filters or fans | no heat recovery |
| can be fitted at the factory or retrofitted | can slightly reduce sound insulation near street noise |
| low cost compared with systems | does not replace airing in short bursts |
You should not overestimate the heat loss from the small airflow: it is intended because it carries moisture away, and at a few cubic metres per hour it lies far below what a permanently tilted window causes. The German Environment Agency expressly advises against permanently tilted windows because they increase energy consumption drastically.
Mind the sound insulation
Every opening in the building envelope is also a path for sound. On busy roads, check whether the chosen vent matches the required sound insulation class or whether sound-attenuated versions are needed. More on this in the article on sound-insulating windows.
Rebate vents compared with other solutions
Besides the rebate vent, there are other window vents and wall solutions that differ in airflow, visibility and effort:
- Surface-mounted or frame vents: they sit visibly on or in the frame, usually at the top, and reach higher air quantities than a rebate vent. Some models offer sound attenuation or filters.
- Wall air inlets (ALD): supply air openings in the wall, independent of the window. They are often combined with an extract system in the bathroom and kitchen.
- Decentralised ventilation units with heat recovery: fan-assisted units in the external wall that work in pairs and recover part of the heat. They need electricity and regular filter changes.
Among these solutions, the rebate vent is the most discreet and simplest, but also the one with the lowest output. It is ideal when the ventilation concept shows only a small gap in moisture protection.
What to look for when choosing
- Airflow at 4 Pa and 8 Pa, because these pressure differences occur frequently in everyday use
- Pressure control, so that no draughts occur in wind
- A variant to suit your profile system and hardware type
- Information on the effect on sound insulation and driving-rain resistance
Fitting: at the factory or retrofitted
Fitting during manufacture is simplest. Position, seal cut-out and hardware are then matched to each other. If you retrofit, follow the manufacturer's instructions exactly:
- The vent is fitted horizontally at the top or, depending on the hardware, on the hinge side between the pivot points.
- The stop seal and centre seal are cut away over the specified length, on both sash and frame.
- On timber windows, routing is needed.
- Depending on the profile, there are variants with different web dimensions.
Mistakes when cutting away the seal can lead to draughts, whistling noises or water ingress. If in doubt, leave the fitting to a specialist firm, not least because a faulty intervention in the seals can affect the window's warranty.
Care and operation
Rebate vents are largely maintenance-free, but not entirely. Dust and insects can collect in the air path. During the annual window care, check that the openings are free and the flap moves. Many models can be closed if necessary, for example in a storm or if a room is left unheated for a long time. For moisture protection, however, they should stay open in normal operation; otherwise the very air change they were fitted for is missing. Explain this to tenants or other occupants too, so that the vents are not accidentally kept closed permanently.
Checklist: planning rebate vents
- Have a ventilation concept prepared if more than a third of the windows are replaced
- Read the volume flow needed for moisture protection from the concept
- Fix the number and position of vents, preferably in bedrooms and living rooms
- Check sound insulation requirements on noisy facades
- State the vents when ordering the windows so that they are fitted at the factory
- Inform the occupants: airing in short bursts is still needed, see avoiding mould after window replacement
If you are planning new windows with a ventilation function, include the requirements from the ventilation concept in your enquiry. Our team answers questions about equipment variants via the contact page; you can create the basic configuration in the configurator.
Frequently asked questions
How does a rebate trickle vent work?
The vent sits in the rebate between sash and frame. Seals are cut away at this point so that a small airflow passes even when the window is closed. A flap throttles the flow as wind pressure rises.
How much air does a rebate vent move?
That depends on the model. For the Siegenia AEROMAT mini, the manufacturer gives about 3 m³/h at 4 Pa, 5 m³/h at 8 Pa and 6 m³/h at 10 Pa pressure difference. Larger window vents reach much higher values.
Does a rebate vent replace short burst ventilation?
No. Rebate vents cover only a small basic air change, typically for moisture protection. For normal use, airing in short bursts is still needed unless the ventilation concept provides for a more powerful system.
Can rebate vents be retrofitted?
On many uPVC windows it is possible, because the vent is fitted into the rebate and the seal is cut away. On timber windows, routing is usually needed. Fitting should follow the manufacturer's instructions and be done professionally.
Sources
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.