Roller Shutters with Anti-Lift Protection: Defence Against Being Pushed Up, and Its Limits
6 minutes read
An anti-lift device stops a closed roller shutter from being pushed up from outside. It connects the top of the curtain to the shaft or blocks the shaft as soon as the shutter is fully down. That is a sensible, inexpensive addition, but not full burglar protection. For targeted protection, the German police recommend tested shutters to DIN EN 1627 from RC2, and point out that the windows themselves must stay secured.
The standards and police advice mentioned here are German. The mechanical principle applies everywhere; if you are outside Germany, please check which security standards and local crime-prevention advice apply.
Why ordinary roller shutters offer little protection
The Polizeiliche Kriminalprävention states that roller shutters can often be overcome fairly easily by simply pushing them up or prising them open. The reasons lie in the construction:
- The curtain hangs loosely on the shaft, usually by suspension springs.
- With the shutter closed, only its own weight or the strap holds the curtain down.
- Thin plastic slats can be pressed in or levered out of the guide rails.
On top of that, many burglaries take place during the day, when shutters are open anyway. The police therefore stress that a roller shutter cannot replace securing the window.
How an anti-lift device works
There are essentially two principles:
Rigid shaft connectors
Instead of flexible suspension springs, rigid connecting elements are fitted between the top slat and the shaft. When the shutter is closed, they lie so that pushing up the curtain cannot turn the shaft, so the curtain is blocked. When pulled up by strap or motor, they wind up normally.
Automatic locks
Other systems work with pawls or springs that engage automatically in the lowest position. Manufacturers such as Schellenberg offer such retrofit kits for their shutter systems in various sizes and describe the effect as reliably preventing the shutter being pushed up from outside.
Additional security at the curtain
In addition, there are bolts or fasteners in the bottom rail that lock the curtain into the guide rails at the bottom. They are usually operated from inside and are particularly practical for basement windows or rarely used rooms.
Retrofitting an anti-lift device: what to look for
| Criterion | What you should check |
|---|---|
| Shaft system | diameter and profile of the shaft (e.g. octagonal shaft) to match the kit |
| Curtain profile | slat height or system size; manufacturers state size ranges |
| Drive | strap, crank or motor; with motors, the end positions may need resetting |
| Number | usually at least two devices, depending on shutter width |
| Space in the box | the extra roll diameter must not rub |
When retrofitting, the box is opened, the curtain is lowered fully and the old suspension springs are swapped for the security devices. With electric drives, it may be necessary to readjust the upper end position. With top-mounted shutters that have a narrow box, you should check beforehand whether there is enough room.
After fitting, run the shutter fully up and down several times and test from outside whether the curtain can still be lifted. If you are unsure, hire a specialist firm; wrongly fitted devices can damage the curtain or jam the motor. How to retrofit a motor is explained in the article Retrofitting a roller shutter motor.
Anti-lift protection and motors
Tubular motors generally hold the shaft firm when stationary. That makes pushing up harder, but is not enough on its own if the curtain hangs loosely on the shaft: the curtain can then be partly lifted even though the shaft is blocked. Only in combination with rigid shaft connectors does this become effective anti-lift protection. Some manufacturers offer matched systems of motor and connector. Also look for obstacle detection, so that motor and device are not damaged by frost or a blockage.
Burglar-resistant roller shutters to DIN EN 1627
If you want targeted protection, choose a burglar-resistant roller shutter. The police recommend shutters to DIN EN 1627 in resistance class RC2 at least. With such elements, the entire construction is tested in practice:
- Curtain: sturdy, usually extruded aluminium slats instead of thin plastic profiles.
- Guide rails: engaging deeply, securely fixed, reinforced against bending open.
- Anti-lift protection: as a tested part of the system.
- Fixing: in load-bearing masonry.
For RC2 roller shutters, KfW loan 159 may come into question in Germany: KfW names burglar-resistant grilles, folding and roller shutters from resistance class RC2 to DIN EN 1627 as an eligible measure (as of September 2026). Simple anti-lift devices do not fall under it. More in the article KfW funding for burglar protection 2026.
External, top-mounted or built-in: differences in security
The design of the roller shutter influences how well it can be secured:
- Built-in roller shutter in the masonry: Box inside, guide rails in the reveal. Anti-lift devices can usually be retrofitted without problems, because the box is accessible from inside.
- Top-mounted roller shutter: The box sits on the window and is delivered with it. When ordering new, the anti-lift device should be ordered at the same time; retrofitting later is often tight in the box. More in the article Top-mounted roller shutters.
- External roller shutter: Box and rails sit outside in front of the façade. That makes them easier to reach, for burglars too. Sturdy aluminium curtains, firmly screwed rails and an anti-lift device are particularly important here. See External roller shutters.
Other weak points of the roller shutter
- Guide rails: Flat or poorly fixed rails can be bent open so that the curtain can be pulled out sideways.
- Slats: Thin plastic slats can be pressed in or cut through. Foam-filled aluminium slats are more resistant.
- Bottom rail: Without locking, the curtain is easier to lift at the bottom.
- Strap: With some designs, the strap can be reached from outside if the box is poorly covered.
An anti-lift device alone closes none of these gaps; it is one building block among several.
What the roller shutter cannot do
- Open by day: An open roller shutter does not protect. Windows therefore need their own security. See Retrofitting burglar protection and Resistance classes RC1 to RC3.
- Occupancy simulation: Permanently closed shutters signal absence. A timer that opens in the morning and closes in the evening looks more natural. More on control in the article Somfy io-homecontrol.
- Escape and rescue routes: Roller shutters in front of windows that serve as a second escape route must be openable in an emergency. With motorised shutters, bear this in mind for power cuts.
Quality marks when buying
The police recommend looking for certification by independent bodies, such as VdS, ift or PfB, for burglar-resistant roller shutters. Such marks show that the product has been tested and production is monitored. For simple retrofit kits, there is generally no comparable testing; they are a sensible obstacle but not certified protection. If in doubt, have the police advice centre explain which combination is appropriate for your house.
Checklist
- Identify vulnerable windows: ground floor, patio, basement.
- Determine the roller shutter system: shaft diameter, slat profile, drive.
- Select a suitable anti-lift device or appoint a specialist firm.
- After fitting, check the motor's end positions and test the function.
- Where targeted protection is needed, choose an RC2 roller shutter to DIN EN 1627.
- Secure the windows as well, because the shutter is open by day.
With new roller shutters, security can be planned in directly. On our page for roller shutters you will find external and top-mounted systems with sturdy aluminium curtains and drive options.
Frequently asked questions
What is an anti-lift device?
A device that locks or blocks the closed shutter curtain against the shaft so that it cannot be pushed up from outside. It is usually fixed to the shaft inside the shutter box and engages automatically when the shutter is fully down.
Can an anti-lift device be retrofitted?
On many built-in and top-mounted shutters, yes. Retrofit kits for common shaft and curtain systems are sold in the trade. Whether a kit fits depends on shaft diameter, slat profile and drive.
Does an anti-lift device make the roller shutter burglar-proof?
It makes pushing up harder but does not turn the shutter into a tested burglar-resistant component. For that, the German police recommend shutters to DIN EN 1627 from RC2, in which curtain, guide rails and security device are tested together.
Do roller shutter motors have a built-in anti-lift device?
Some drives hold the curtain through the motor brake, but that only replaces an anti-lift device if it is combined with a mechanical connection between shaft and curtain. Which solution the manufacturer provides is stated in its documentation.
Sources
- Polizeiliche Kriminalprävention (K-Einbruch): Rollläden(opens in a new tab)
- Polizeiliche Kriminalprävention (K-Einbruch): Fenster sichern(opens in a new tab)
- Schellenberg: Rollladensicherungen und Hochschiebesicherungen(opens in a new tab)
- KfW Anlage zum Merkblatt 159: Technische Mindestanforderungen(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.