Repairing a Roller Shutter: Spotting and Fixing Strap, Slat and Motor Faults
7 minutes read
In many cases you can repair a roller shutter yourself: replacing the strap, swapping the strap winder, replacing slipped or broken slats and renewing bottom rails are typical DIY jobs. Take care with the strap winder, because it is under spring tension. Work on the motor and electrics belongs in the hands of a qualified electrician. If several parts are worn at the same time, a new roller shutter with an insulated box is often worthwhile.
How a roller shutter is built: the main parts
- Curtain: the slats made of plastic or aluminium, with a bottom rail.
- Shaft: usually an octagonal steel shaft in the box, onto which the curtain winds.
- Suspension: springs or rigid connectors between the top slat and the shaft.
- Bearings: at both ends of the shaft.
- Drive: strap with strap pulley and strap winder, crank with gearbox, or a tubular motor in the shaft.
- Guide rails: at the side in the reveal or in front of the façade.
- Stop plugs: prevent the curtain from being pulled too far into the box.
Fault diagnosis: what is broken?
| Symptom | Probable cause | DIY possible? |
|---|---|---|
| Strap torn or frayed | wear, chafing strap guide | yes, with care |
| Strap no longer winds up | spring in the strap winder broken | yes, replace the winder |
| Roller shutter hangs crooked | slat slipped, suspension torn | mostly yes |
| Curtain slides right into the box | stop plugs missing or broken off | yes |
| Slats broken or bent | hail, force, ageing | yes, individual slats |
| Roller shutter jams in the rails | dirty or bent rails, frost | cleaning yes, replacing rails possibly a specialist firm |
| Motor does not run | switch, fuse, control unit, motor | qualified electrician |
| Motor stops at the wrong position | end positions misadjusted | depends on the motor, with instructions |
Replacing the roller shutter strap
The strap is the part that wears out most often. Proceed like this:
- Lower the roller shutter fully. The strap is then wound up to the maximum on the winder and the curtain is down.
- Open the strap winder: unscrew the cover and carefully pull the winder out of the wall. The spring is under tension; hold the strap firmly and let it run out slowly.
- Open the inspection cover of the box and release the old strap from the strap pulley.
- Fix the new strap: hook it onto the top of the strap pulley and wind on a few turns, then feed it down through the strap opening.
- Fix the strap to the winder and set the spring tension: the winder should wind the strap up taut when the shutter is raised.
- Check the function and close the box again; take the opportunity to seal the cover. See Insulating roller shutter boxes.
Pay attention to the correct strap width (mini or standard system). Manufacturers such as Schellenberg label accessories for different system sizes.
Replacing the strap winder
If the spring in the winder breaks, the strap no longer winds up. A new surface-mounted or recessed winder is fitted as when replacing the strap. With a recessed winder in the wall, the size must match the recess. There are also electric strap winders that are fitted in place of the manual winder and motorise the shutter without altering the shaft.
Repairing or replacing slats
Slipped slats
Slats can wander sideways and rub on the rails. With the shutter lowered, they can often be pushed back with light taps of a rubber mallet. To stop this happening again, there are slat locks or end caps.
Broken slats
Individual slats can be replaced by guiding the curtain out over the box from above or sideways out of the guide rail. The new slat must match the profile exactly. With older roller shutters, the matching profile is sometimes no longer available; a new curtain can then make sense.
Bottom rail and stop plugs
The bottom rail finishes the curtain and carries the stop plugs. If they are missing, the curtain is pulled completely into the box when raised. New stop plugs are simply screwed or clamped into the bottom rail.
Guide rails and running noise
If the roller shutter jams or squeaks, the guide rails are often the cause. Leaves, insects and dust collect in them and slow the curtain. Clean the rails with a brush and a damp cloth. A silicone-based lubricant can help; oil or grease, on the other hand, attract dirt and should not be used. If rails are bent, for example after an attempted break-in or a storm, they usually have to be replaced. With external roller shutters, the rails are screwed on outside and are easier to replace than with built-in shutters set in plaster.
Preventive maintenance
Many repairs can be avoided if the roller shutter is briefly checked once or twice a year:
- Check the strap for frayed spots and the strap guide for sharp edges.
- Inspect slats and bottom rail for cracks, and check the stop plugs.
- Clean the rails.
- In winter, do not force the shutter open in frost; with motors, use the control unit's frost-protection function if there is one.
- Open the inspection cover and look at suspensions and bearings, taking the chance to look for draughts and traces of moisture.
Motor and electrics
Tubular motors sit in the shaft and have set end positions. If the motor stops too early or too late, the end positions can be reset on many models following the manufacturer's instructions, either mechanically via adjusting screws or electronically via the control unit. Somfy and other manufacturers provide instructions online.
Important:
- Work on the 230-volt connection may only be carried out by qualified electricians (mains voltage in Germany; check the voltage and rules where you live).
- Do not operate it continuously if the motor hums but nothing moves; that can trip the thermal protection or damage the motor.
- Frost: In winter the curtain can freeze to the window cill. Motors with obstacle detection then stop; older motors can damage the curtain or suspension.
If you would like to change from strap to motor, you will find advice in the article Retrofitting a roller shutter motor.
When a specialist firm or a new roller shutter makes sense
- The shaft is bent or the bearings are worn out.
- The box is hard to reach or plastered over.
- The curtain is brittle or discoloured over large areas.
- Motor or control unit are faulty.
- The roller shutter is to become more secure at the same time, for example with an anti-lift device; see Roller shutters with anti-lift protection.
You can find specialist firms through the specialist-firm search of the Bundesverband Rollladen + Sonnenschutz, among others. With old built-in boxes that are leaky anyway, a new external or top-mounted roller shutter is often the more lasting solution. An overview is given in the article Roller shutter types compared.
A safety note: with roller shutters on upper floors, never work leaning out of an open window without fall protection, and do not let the curtain drop uncontrolled. The curtain of a large roller shutter can weigh a considerable amount.
Checklist
- Observe the symptom and narrow down the cause.
- Determine the system size (mini/standard) and profile before ordering spare parts.
- Open the strap winder only with the spring tension secured.
- Have electrics worked on only by qualified people.
- Seal the box while you are repairing.
- If there are several defects, consider buying new.
If the roller shutter can no longer be saved, our page for roller shutters offers made-to-measure systems with strap, crank or motor.
Frequently asked questions
How do I replace a torn roller shutter strap?
Lower the shutter and secure it, open the inspection cover, release the old strap from the strap pulley, fix the new strap to the pulley and the strap winder, and set the spring tension of the winder correctly. Caution: the strap winder is under spring tension.
Why does my roller shutter hang crooked?
Often the suspension springs have broken, a slat has slipped sideways or a bearing is worn. Slats that have slipped sideways can often be pushed back with the shutter lowered; broken suspensions have to be replaced.
The roller shutter motor hums but nothing moves. What should I do?
Possible causes are a curtain frozen in place, an obstacle, a jammed bearing or a faulty capacitor or motor. Do not operate it repeatedly; check the cause and, for anything electrical, call a qualified electrician.
When is a new roller shutter worthwhile instead of a repair?
When several components are worn at the same time, the box is leaky and uninsulated or slats are becoming brittle. A new shutter with an insulated box can then make more sense.
Sources
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.