Roller Shutter and Window Cill: How to Plan Guide Rails, Bottom Rail and Sealing Properly
6 minutes read
At the connection between roller shutter and window cill, three trades meet: window, roller shutter and façade. To keep everything watertight, guide rails, cill and bottom rail must be coordinated. Either the rails end on the cill, or the cill is notched in the rail area. In both cases: water must drain in front of the façade and must not run along the rails behind the cill.
Why this interface is so prone to faults
Many requirements come together at the lower edge of the window:
- The window cill needs fall, projection and a drip edge so that rain runs off the façade.
- The guide rails of the roller shutter must be firmly fixed and guide the curtain right to the bottom.
- The bottom rail should sit tightly when closed without freezing fast in winter.
- The sealing of the window connection must not be damaged by screws and notches.
If any of these requirements is ignored, gaps, water stains on the parapet or render damage result. You can read the basics on window cills in the article External and internal window cills.
Roller shutter and window cill: the typical connection variants
| Variant | Description | Advantages | Points to note |
|---|---|---|---|
| Rail ends on the cill | rails set onto the cill with end pieces | no intervention in the cill | seal the rail foot, allow for fall |
| Cill notched | cill cut out in the rail area, rail runs down to the parapet | clean straight look | seal the notch and side ends carefully |
| Rail ends above the cill | rail ends just above | simple fitting | curtain must stay safely in the rail; more for retrofits |
| Rail in the reveal in front of the cill | rails in a recess at the side | protected | only with a suitably planned reveal |
External roller shutters: retrofitting in front of the façade
With an external roller shutter, the box sits outside, and the rails run in front of the façade or in the reveal. For retrofits, the cill is usually already there. What matters here:
- Check the projection: The cill must project far enough that rails and curtain have room above it and water still drips off in front of the façade.
- Rail foot: End caps or rail feet compensate for the fall and stop water standing in the rail.
- Fixing: The rails are screwed into the reveal or the façade. With insulated façades (external wall insulation), you need suitable fixings that do not hold only in the insulation.
More on the system in the article External roller shutters.
Top-mounted roller shutters: plan them in when replacing windows
With a top-mounted roller shutter, box and rails are delivered with the window. That is the best opportunity to plan the cill to match. The rails are often fixed to the window frame or in the reveal and end on the cill or in a notch. Agree on:
- Cill depth and projection beyond the finished façade,
- Rail depth and distance to the window frame,
- Connection profile under the window that receives the cill; see cill connection profile (FBA),
- Render build-up at the reveal so that rails and render meet cleanly.
Details on the system in the article Top-mounted roller shutters.
Sealing at the rail and window cill
The window cill is a water-bearing layer. Every penetration is a potential leak. Note:
- No screws through the cill if it can be avoided. If they are needed, seal them.
- Cut notches cleanly, deburr edges and connect side end profiles or sliding end caps correctly.
- Second water-bearing layer under the cill, as installation guidelines require in many cases, so that water that runs past a rail still reaches the outside.
- Do not cover the window's drainage: The drainage openings in the frame must stay clear.
Bottom rail and end position
The bottom rail is the lowest profile of the roller shutter curtain. When closed, it should sit evenly on the cill:
- Compensate for the fall: Because the cill slopes outwards, a straight bottom rail sits only on the front edge. Bottom rails with a rubber lip compensate for this.
- Set the end position: With motors, choose the lower end position so that the curtain sits on the cill but is not compressed. Too much pressure stresses suspension and slats.
- Frost: If the bottom rail sits in standing water, it can freeze fast. Good fall and obstacle detection in the motor prevent damage.
- Security: A bottom rail that sits firmly, together with an anti-lift device, makes it harder to lift the curtain. More in the article Roller shutters with anti-lift protection.
Typical damage and its causes
| Damage pattern | Common cause | Remedy |
|---|---|---|
| Damp parapet under the rail | notch or rail foot not sealed, no second water-bearing layer | open the connection, add under-cill sealing |
| Water stands in the rail | rail on the cill without drainage | rail foot with water outlet, check the fall |
| Bottom rail freezes fast | water collects under the bottom rail | improve fall, bottom rail with seal, frost-protection function in the motor |
| Cracks in the render at the reveal | rails rigid in the render, no movement joint | make the connection joint elastic |
| Gap under the curtain | end position wrong, fall not allowed for | set the end position, matching bottom rail |
Many of these problems show up only in the first winter. A water test with a watering can at handover reveals the grossest faults beforehand; see Acceptance and handover.
Built-in and old-building roller shutters
With old built-in roller shutters, the guide rails often run in grooves in the reveal or are set in plaster. If only the window is replaced, the rails often have to be kept, and the new cill must follow them. Before ordering, therefore, measure the position of the rails in relation to the window plane. If the cill depth no longer fits, cill connection profiles or shorter or longer external cills help. If the old box is to be replaced anyway, a top-mounted roller shutter with a new cill is the cleanest solution. Advice on box insulation in the article Insulating roller shutter boxes.
Order of work on site
- Fit the window and seal the connection following the three-layer principle.
- Fit the cill with under-cill sealing and side ends.
- Set the guide rails, notching the cill if necessary.
- Plaster the reveal or close the façade.
- Adjust the roller shutter, check end positions, water test at the cill.
If the order is reversed, for example by plastering first and then sliding in the cill, there is a risk of a leaky connection. The installation basics are described in the article RAL installation.
Dimensions that must be fixed before ordering
- Façade build-up: render thickness and, where applicable, insulation thickness, so that cill and rails are sized correctly.
- Cill projection: about 40 mm beyond the finished façade as the usual guide figure in installation guidelines.
- Rail depth and width: according to the roller shutter manufacturer, including the distance to the window sash.
- Reveal width: whether the rails fit into the reveal or sit in front of the façade.
- Height of the cill in relation to the lower edge of the frame and to the connection profile.
Planning checklist
- Decide on the shutter type: external, top-mounted or built-in.
- Determine the cill depth including projection beyond the finished façade.
- Choose the connection variant: rail on the cill or notch.
- Plan the sealing and the second water-bearing layer.
- Provide a bottom rail with a seal and a suitable end position.
- Coordinate the trades: window fitter, roller shutter, façade.
Window and roller shutter from a single source make coordination easier. In the configurator you plan windows with a matching roller shutter; you will find an overview of the systems on our page for roller shutters.
Frequently asked questions
Do roller shutter rails stand on the window cill?
In many installation situations, the guide rails end on the external window cill. The cill is then either notched in the area of the rails, or the rails are set onto the cill with suitable end pieces. What matters is that no water gets behind the cill at this point.
Does the cill have to be notched for an external roller shutter?
Often yes, if the rails are to run down to the parapet. Alternatively, rails can stand on the cill. Which solution fits depends on the cill projection, rail depth and façade.
Why is there a gap between my roller shutter and the window cill?
Often the lower end position is set wrongly, the cill has more fall than expected or the bottom rail does not match the fall. A bottom rail with a rubber seal and correctly set end positions close the gap.
Who plans the connection between roller shutter and window cill?
Ideally the window fitter together with the roller shutter supplier and the façade contractor. Dimensions for cill projection, rail depth and render build-up must be fixed before ordering.
Sources
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.