Frame Depth in Windows: Why More Millimetres Are Not Automatically Better
7 minutes read
The frame depth of a window states how deep the outer frame sits in the wall from inside to outside – usually 70 to 88 mm for uPVC windows. More depth creates room for additional chambers, a centre seal and thicker glass. But it is not a quality measure in itself: the Uf-value is what counts, and in older homes too much depth can complicate the connection and the internal window board.
What frame depth exactly is
What is measured is the depth of the outer frame – the part of the frame fixed in the wall. The sash can differ: with Schüco AWS 90.SI+ the outer frame is 90 mm, and according to manufacturer data the sash is 100 mm; with Kömmerling K-VISION it is 120 mm in the frame and 76 mm in the sash, because the frame has a special outer contour. When a quote says "82 mm", it generally means the frame depth of the outer frame.
What more frame depth makes possible
More chambers
A deeper profile geometry allows additional air chambers that interrupt heat flow. Kömmerling quotes a 5-chamber construction for 70 mm and a 7-chamber construction for 88 mm.
A third seal level
Centre-seal systems need space in the rebate. That is why they are found mainly in profiles from around 76 mm. The advantages are described in the article Centre seal vs rebate seal.
Thicker glazing
The glazing range grows with frame depth. Kömmerling quotes glass thicknesses of 10 to 44 mm for 70 mm and up to 60 mm for 88 mm. That matters for thick triple, acoustic and safety glass.
Better integration into the insulation plane
A deeper frame bridges more wall thickness and is easier to connect with external insulation. That reduces thermal bridges at the connection.
Why more millimetres are not automatically better
The following table shows published manufacturer values (as of September 2026). It makes clear that frame depth alone says little about insulation:
| System | Frame depth | Seal | Uf according to manufacturer |
|---|---|---|---|
| Kömmerling 70 AD | 70 mm | Rebate | up to 1.2 W/(m²K) |
| Kömmerling 76 MD | 76 mm | Centre | up to 1.0 W/(m²K) |
| REHAU Artevo (LowE) | 80 mm | Centre | down to 0.81 W/(m²K) |
| Schüco LivIng Classic 82 AS | 82 mm | Rebate | up to 1.0 W/(m²K) |
| Schüco LivIng Classic 82 MD | 82 mm | Centre | up to 0.96 W/(m²K) |
| Kömmerling 88 MD | 88 mm | Centre | 0.93–0.98 W/(m²K) |
Observations:
- An 80 mm profile with LowE technology undercuts, according to the manufacturer, the Uf-value of the 88 mm standard system.
- An 82 mm profile with a rebate seal reaches the same best value as a 76 mm profile with a centre seal.
- Chamber geometry, seal, reinforcement and insulating inserts determine the Uf-value at least as strongly as depth.
So compare profiles by the Uf-value of the specific version, not by frame depth. How to do that is explained in the article Uf-value of the frame.
When a large frame depth has drawbacks
Tight reveal in an older home
In many existing buildings the old window sits in a masonry rebate of limited depth. A deeper frame then reduces the support for the internal window board or protrudes beyond the inner edge of the reveal. Sometimes internal plaster or the window board must be adapted – which costs time and money.
Roller shutter boxes and connection profiles
Surface-mounted roller shutters, window-board connection profiles and frame extensions are matched to the frame depth of the system. When switching to a deeper profile, these components must be planned in.
Weight and price
Deeper profiles and thicker glass are heavier and more expensive. If the building only needs to meet the statutory minimum requirement, this extra effort is not always justified.
Daylight
Frame depth itself hardly changes the glass area – what matters for light is the face widths. Deep systems often also have wider sightlines, though. How to bring more light into the house is described in the article Slim face widths.
Which frame depth for which project?
| Project | Recommended frame depth | Reason |
|---|---|---|
| Cellar, garage, ancillary rooms | 70 mm | low requirements, tight space |
| Older home with narrow reveal | 70–76 mm | installation without major adjustments |
| Renovation with BEG funding | 76–82 mm with centre seal | Uw ≤ 0.95 W/(m²K) reachable |
| New build standard | 80–88 mm | good integration into insulated wall |
| Passivhaus | 80–88 mm in certified version | low Uf-values, certificate |
German BAFA individual-measure funding requires Uw ≤ 0.95 W/(m²K), and the basic funding rate is 15% (as of September 2026). No minimum frame depth is prescribed – only the proven Uw-value counts. In the UK or elsewhere, check the local thermal limits and schemes.
How to measure the available depth
- Measure the reveal depth: from the inner edge of the masonry rebate to the outer edge of the wall or insulation.
- Decide the installation position: should the window sit in the middle, flush outside or in the insulation plane?
- Allow for the connection joint: an airtight tape inside, sealing outside – both need space.
- Plan the internal window board: does the support still suffice if the frame gets deeper?
- Check the roller shutter: does the existing or planned box suit the new frame depth?
How to prepare the work properly is described in the article Measuring windows correctly.
Example: replacing 70 mm with 82 mm in an older home
A typical case: a house from the 1980s has uPVC windows with about 60 to 70 mm frame depth in a masonry rebate. The owners want to switch to an 82 mm system with a centre seal. What changes:
- Inside: the new frame projects about 12 to 22 mm further into the room. The old internal window board loses support accordingly and may need to be shortened or replaced.
- Outside: if the window sits further out, the connection to later external insulation often improves.
- Roller shutter: an existing surface-mounted box no longer fits; a front-mounted roller shutter is unaffected.
- Connection joint: the new joint must be made airtight inside and driving-rain-tight outside – in older buildings often with levelling of uneven reveals.
The extra effort is usually manageable but should be included in the quote. Ask whether internal window board, making-good plaster and connection work are allowed for.
Frame depth and sound insulation
Sound insulation depends mainly on the glazing. Deeper profiles help indirectly, because they can take thicker and asymmetrically built acoustic glass. Kömmerling quotes sound insulation of up to 47 dB for 76 mm systems and up to 48 dB for 88 mm – the difference lies more in the glazing latitude than in the frame depth itself.
Frame depth on aluminium windows
With aluminium too, more depth allows a wider insulation zone. Schüco offers AWS 75.SI+ and AWS 90.SI+, for instance. Aluminium, however, is stiffer than PVC and needs no reinforcement, so there frame depth decides mainly insulation, not stability.
Conclusion and checklist
- Frame depth is a construction dimension, not proof of quality.
- Compare profiles by the Uf-value of the specific version.
- In an older home, measure the reveal first, then choose the system.
- For funding, the Uw-value of each window counts.
- Plan accessories such as roller shutter box, window-board connection and extensions as well.
In the AluKun configurator you choose the profile system with the right frame depth. If you are unsure which depth fits your reveal, send us dimensions and photos through the contact form.
Frequently asked questions
What does frame depth mean for a window?
Frame depth is the dimension of the outer frame from the inside to the outside, that is, how deep the profile sits in the wall. For uPVC windows, usual values lie between 70 and 88 mm.
Does a window with greater frame depth automatically insulate better?
Not automatically. More depth creates room for chambers, seals and thick glass, but the Uf-value is what counts. REHAU, for instance, quotes a better Uf-value for Artevo at 80 mm frame depth than Kömmerling does for its 88 mm standard system.
What frame depth do I need in an older home?
That depends on the reveal. 76 to 82 mm often fits well; with narrow rebates a 70 mm profile can be easier. Measure the available depth including connection joint and internal window board.
What frame depth is needed for BAFA funding?
German funding does not prescribe a minimum frame depth. What is required is a Uw-value of at most 0.95 W/(m²K). In practice that is usually reached with profiles from around 76 mm and triple glazing.
Sources
- Kömmerling 70 Anschlagdichtung Standard – Produktseite(opens in a new tab)
- Kömmerling 76 Mitteldichtung Standard – Produktseite(opens in a new tab)
- Kömmerling 88 Standard – Produktseite(opens in a new tab)
- Schüco LivIng Classic – Datenblatt (PDF)(opens in a new tab)
- REHAU – Premium-Fenstersystem ARTEVO(opens in a new tab)
- Kömmerling K-VISION – Produktseite(opens in a new tab)
- BAFA – BEG Einzelmaßnahmen Gebäudehülle(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.