Centre Seal vs Rebate Seal: Window Sealing Systems Explained
6 minutes read
A centre seal on a window is a third seal level in the middle of the rebate between outer frame and sash. Rebate-seal systems, by contrast, have only two seals – outside and inside. The centre seal separates a wet from a dry rebate zone, usually improves the Uf-value by around 0.1 W/(m²K) and protects the hardware. For funded projects and noise protection it is the more sensible choice; for ancillary rooms the rebate seal is often enough.
How the rebate seal works
With the rebate seal there are two continuous seals in the window:
- Outer seal: usually sits on the outer frame and rests against the sash overlap. It keeps out driving rain and wind.
- Inner seal: sits on the sash and rests against the outer frame. It provides airtightness towards the room side.
Between them lies a continuous rebate space, in which the hardware also sits. Water that gets past the outer level is drained outwards through drainage slots. The principle is proven and widespread in uPVC windows.
How the centre seal works
With a centre-seal system, a third seal is added, sitting roughly in the middle of the rebate. This creates two separate zones:
- Outer rebate space: water that has got in is collected here and drained away.
- Inner rebate space: it stays dry and warm. The hardware sits here, protected.
The WERU technical information describes the centre seal as forming "two chambers" and so improving protection against air and moisture. It also reduces air movement in the rebate, which lowers heat loss and sound transmission.
The differences in figures
Manufacturer data for systems that exist in both variants show how big the effect is (as of September 2026):
| System | Rebate seal | Centre seal |
|---|---|---|
| Kömmerling 76 (Uf) | up to 1.1 W/(m²K) | up to 1.0 W/(m²K) |
| Schüco LivIng Classic 82 (Uf) | up to 1.0 W/(m²K) | up to 0.96 W/(m²K) |
| Kömmerling 76 (glass thickness) | 16–52 mm (76223 sash up to 58 mm) | 4–56 / 26–60 mm |
| Sound insulation (both systems) | up to 47 dB | up to 47 dB |
Striking: for sound insulation, both manufacturers quote the same maximum values for AD and MD. Sound insulation is achieved mainly through the glazing; the centre seal helps the window deliver these values reliably over the long term.
Advantages of the centre seal
- Better Uf-value: the difference is small, but on small windows it can decide the funding threshold of Uw ≤ 0.95 W/(m²K).
- Protected hardware: the hardware sits in the dry zone and is less exposed to moisture and dirt.
- More security against leaks: an additional level provides reserve if a seal ages.
- Often a wider glazing range: with Kömmerling 76 MD, up to 60 mm is possible.
Advantages of the rebate seal
- Proven and simple: fewer components, easier seal replacement.
- Slightly cheaper: usually a lower price than the MD variant of the same system.
- More variants: some design lines, such as Kömmerling K-VISION, exist only as a rebate seal.
- Sufficient for rooms without particular requirements for insulation and noise protection.
Centre seal on aluminium windows
Aluminium systems also use centre seals. For AWS 75.SI+, Schüco describes a "large-volume centre seal". With aluminium it has an additional job: it closes off the insulation zone between the outer and inner shell and prevents cold air from flowing through the rebate into the thermal break. That is why highly insulated aluminium windows are practically always centre-seal systems. The principle of the insulation zone is explained in Aluminium windows: thermal break.
Misunderstandings about seals
"Three seals = three times as airtight." A window's airtightness is tested in classes under the standard, and many rebate-seal systems also reach the top class. The advantage of the centre seal lies mainly in separating the wet and dry zones and in thermal protection, not in multiplied airtightness.
"The centre seal replaces good installation." No. In practice, draughts often arise at the connection joint between frame and wall or from incorrectly adjusted hardware. A window with a centre seal that is installed without an airtight connection tape will still be draughty.
"The rebate seal is outdated." The principle is proven and is being developed further in current systems. With LivIng 82 AS, Schüco reaches a Uf of up to 1.0 W/(m²K) – on the level of some centre-seal systems with less frame depth.
Effect on hardware adjustment
A seal only works if the sash closes with the right contact pressure. With centre-seal systems, three seal levels must bear on the sash at the same time, so the hardware must be adjusted correspondingly carefully. After installation and after a few months of settling, a specialist firm should check the contact pressure and, where necessary, readjust via the eccentrics of the locking pins. Many hardware sets offer a winter and summer setting for this – slightly higher contact pressure in winter, slightly lower in summer to spare the seals.
Seal colour
Seals mostly come in grey or black, and with some systems also in beige or white. On white windows a grey seal looks more discreet, and on dark decors a black one. The colour does not affect function but should be decided when ordering, because changing it later is laborious.
Seal material and care
Besides the system, the material counts. Many profile manufacturers use EPDM or thermoplastic elastomers (TPE). For EPDM, WERU stresses high temperature resistance and long-lasting elasticity. Whatever the material:
- Clean seals once a year and treat them with a seal care stick.
- Do not paint over them – paint makes seals hard.
- Pulled-in seals can be replaced when worn; ask about the system seal.
More on replacement in the article Window seals: material, replacement, care.
Centre seal and burglar resistance
It is often assumed that the centre seal makes a window more burglar-resistant. That is not the case: burglar resistance results from hardware with mushroom-head locking pins, security strike plates, a lockable handle, glazing and screw fixing in the reinforcement. For 76 AD and 76 MD alike, Kömmerling quotes "up to RC 2". The centre seal does, however, protect the hardware better from moisture and dirt, which preserves its function in the long term.
Decision guide
| Situation | Recommendation |
|---|---|
| Renovation with BEG funding | Centre seal |
| Road noise, acoustic glazing | Centre seal |
| Exposed location with driving rain | Centre seal |
| Cellar, garage, ancillary room | Rebate seal |
| Particular design line only available as AD | Rebate seal |
| Highly insulated aluminium window | Centre seal (system standard) |
Which systems use which seal is shown in the articles Kömmerling 76 and uPVC window profile comparison. The BEG funding referred to is German; in the UK or elsewhere, check the thermal limits and schemes that apply to you.
Checklist
- Clarify the requirement: funding, noise, location.
- Choose a system that offers the right seal variant.
- Have the Uf-value of the specific variant stated in the quote.
- Check the glass thickness if special glazing is planned.
- Plan maintenance: check seals and hardware annually.
- Decide the seal colour: grey or black to match the profile and decor.
- Adjustment after installation: have a specialist firm check the contact pressure after a few months.
In the AluKun configurator you can see for each profile system whether it is built with a rebate seal or a centre seal. If you are torn between two variants, tell us the window dimensions, location and funding goal – we will recommend the right combination.
Frequently asked questions
What is a centre seal on a window?
An additional seal, usually fitted to the outer frame, in the middle of the rebate between frame and sash. It divides the rebate space into an outer, water-carrying zone and an inner, dry zone.
Is the centre seal always better?
It generally improves thermal and sound insulation and protects the hardware. Whether the extra cost is worthwhile depends on the goal: usually yes for funded projects and noisy locations, often unnecessary for ancillary rooms.
How much better insulation does the centre seal bring?
At the same frame depth, manufacturers often quote Uf-values around 0.1 W/(m²K) better for the MD variant. For Kömmerling 76, the manufacturer quotes up to 1.1 (AD) against up to 1.0 W/(m²K) (MD).
Can a rebate seal be converted to a centre seal?
No. A centre seal requires a matching profile geometry with a groove. Only worn seals of the same system can be replaced.
Sources
- Kömmerling 76 Mitteldichtung Standard – Produktseite(opens in a new tab)
- Kömmerling 76 Anschlagdichtung Standard – Produktseite(opens in a new tab)
- Kömmerling – 76-mm-Systeme(opens in a new tab)
- Schüco LivIng Classic – Datenblatt (PDF)(opens in a new tab)
- WERU Lexikon – Fensterdichtungen(opens in a new tab)
- Schüco Systemeigenschaften AWS 75.SI (PDF)(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.