Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Window profiles

Steel Reinforcement in uPVC Windows: When It Is Needed and What the Alternatives Are

6 minutes read

Steel reinforcement in a uPVC window is needed whenever size, glass weight, wind load or colour would overstretch the PVC profile alone. It sits as a galvanised steel section in a chamber of the frame and sash and keeps the window dimensionally stable in the long term. Whether and which reinforcement is used is set by the profile manufacturer in its fabrication guidelines. Newer systems partly replace steel with fibre-reinforced materials.

Why PVC has to be stiffened

Compared with aluminium or wood, PVC has two properties that are critical for a window:

  • Lower stiffness: a long, narrow PVC profile sags more under load.
  • Temperature dependence: PVC expands with heat and becomes softer. Dark surfaces in particular heat up strongly in the sun.

Without reinforcement, sashes with heavy triple glazing could drop, frames could deform under wind load, or hardware could lose its fixing. The consequences would be leaking windows, stiff sashes and, at worst, broken glass.

How the reinforcement is fitted

The steel sections – usually galvanised steel, as U, L or rectangular sections – are pushed into the main chamber of the profile intended for them and screwed in before the frame corners are welded. This creates a composite that also holds the screws of the hardware and of the fixing in the wall securely.

Exactly where the reinforcement lies affects insulation. For the Passivhaus version of the 88 mm system, for instance, Kömmerling describes a "centrally arranged steel reinforcement" – the position in the middle of the profile keeps the steel away from the cold and warm outer surfaces.

When is reinforcement mandatory?

Binding requirements come not from a general standard but from the system supplier. Each profile manufacturer specifies in its fabrication guidelines which reinforcement is to be used under which conditions. Typical criteria are:

Criterion Effect
Sash and frame size large sashes and long frame members need more stiffness
Glass weight thick triple, acoustic and safety glass increase the load
Colour and decor dark surfaces heat up more
Wind load tall buildings and exposed locations require stiffer profiles
Burglar resistance RC-tested windows require defined reinforcements
Hardware heavy hardware and special opening types need support

For clients that means: you do not have to calculate the reinforcement yourself, but you should make sure a qualified window maker fabricates to the system supplier's guidelines. According to the Gütegemeinschaft Kunststoff-Fensterprofilsysteme (the German uPVC window profile quality association), uPVC profile systems with the RAL quality mark under RAL-GZ 716 are subject to initial testing and independent monitoring, including tests on large test windows.

Special case: coloured windows

Dark decors such as anthracite grey or walnut absorb more solar energy than white profiles. The profile becomes warmer, expands more and loses stiffness. Fabrication guidelines for foil-laminated windows therefore often prescribe more extensive reinforcement or smaller maximum sash sizes. Foil manufacturers work against the heating: for EXOFOL MX, RENOLIT uses pigments with Solar Shield technology that, according to the manufacturer, are meant to reduce excessive heat build-up in the profile.

How large the influence of colour can be is shown by Kömmerling's figures for 88 proStratoTec: with glass bonding, sashes are possible in white up to 1,000 × 2,500 mm and in decor up to 1,000 × 2,350 mm; without bonding, in white up to 1,000 × 2,200 mm and in decor up to 1,000 × 1,800 mm. More on colour choice in the article Anthracite outside, white inside.

Steel as a thermal bridge

Steel conducts heat much better than PVC. In the profile chamber it therefore acts as a thermal bridge and worsens the Uf-value. Manufacturers counter this in three ways:

  1. Optimised position: reinforcement in the centre, far from the surfaces.
  2. Reduced cross-sections: only as much steel as structurally necessary.
  3. Alternative materials: fibre composite instead of steel.

Alternatives: fibre-reinforced profiles

REHAU RAU-FIPRO X

With Artevo, REHAU uses a glass-fibre-reinforced material across the whole profile cross-section. According to the manufacturer, the system thereby manages "largely without steel reinforcement", and elements without steel are up to 40% lighter than classic uPVC windows. For very tall sashes, a reinforcement is still available. Details in the article REHAU Artevo.

Kömmerling proStratoTec

With Kömmerling 88 proStratoTec, a glass-fibre reinforcement (Ultradur) is integrated into the profile. According to the manufacturer, steel can thereby be omitted, mainly in the sash, which improves the Uf-value to 0.77 to 0.89 W/(m²K). More in the article Kömmerling 88.

Glass bonding

In many modern systems the pane is bonded to the sash profile. The glass then contributes structurally and stiffens the sash. That is why manufacturers distinguish between bonded and non-bonded versions for maximum sash sizes.

And with aluminium?

Aluminium profiles are self-supporting and need no steel reinforcement. That is one of the reasons why aluminium windows allow larger sashes with slimmer sightlines. More in the comparison uPVC or aluminium.

Reinforcement in additional profiles

It is not only frames and sashes that are stiffened. Larger frame extensions and structural couplings between window and door elements also contain steel or aluminium, so that they carry loads from wind and lintel safely.

How to spot problems

Missing or inadequate reinforcement usually shows only after a few years:

  • Sash rubs against the frame or can only be closed with pressure.
  • Visible deflection of long frame members, for example at the top of the outer frame of wide windows.
  • Draughts at individual points because the seal no longer bears evenly.
  • Loosened hardware screws because they sit only in the PVC rather than in the steel.

Such symptoms can also have other causes, such as a misadjusted lock or settlement in the masonry. If in doubt, have a specialist firm check before you readjust.

Retrofitting is not possible

Reinforcement is pushed in during manufacture before welding. It cannot be fitted afterwards. The decision at purchase is therefore final – another reason to insist on fabrication to the system supplier's guidelines.

Reinforcement and fixing in the wall

The reinforcement also serves installation: frame plugs and installation screws pass through the PVC into the steel. This is how wind loads and the weight of the window are transferred safely into the wall. For fibre-reinforced profiles without steel, manufacturers give their own fixing specifications and approved screws. Make sure the installer knows these specifications.

Checklist for your quote

  1. Choose a profile system with the RAL quality mark.
  2. Ask the window maker whether reinforcement follows the system supplier's fabrication guidelines.
  3. For dark colours, ask about maximum sash sizes and reinforcement.
  4. For large formats, clarify whether glass bonding is used.
  5. For RC windows, make sure the tested construction, including reinforcement, is fabricated.
  6. For fibre-reinforced systems, ask about approved dimensions without steel and about fixing specifications.

In the AluKun configurator you choose dimensions, colour and glazing; fabrication follows the specifications of the respective system supplier. We answer questions about the feasibility of large or coloured formats through the contact form.

Frequently asked questions

Why do uPVC windows need steel reinforcement?

PVC is less stiff than wood or aluminium and expands more with heat. Reinforcement in a profile chamber ensures that frame and sash permanently carry glass weight, wind load and hardware forces without deforming.

Who decides whether a window is reinforced?

The profile manufacturer (system supplier) specifies in its fabrication guidelines which reinforcement is to be used from which dimensions, colours and loads. The window maker must follow these specifications.

Are there uPVC windows without steel?

Yes. REHAU Artevo uses the fibre-reinforced RAU-FIPRO X material and, according to the manufacturer, largely dispenses with steel; Kömmerling uses glass-fibre reinforcement in 88 proStratoTec, so that steel can be omitted in the sash.

Does steel worsen insulation?

Steel conducts heat much better than PVC and acts as a thermal bridge in the profile. Manufacturers therefore optimise the position and shape of the reinforcement; fibre-reinforced solutions can improve the Uf-value.

Sources

  1. Kömmerling 88 Passivhaus WA15/2 – Produktseite(opens in a new tab)
  2. Kömmerling 88 proStratoTec – Passivhausfenster zertifiziert nach PHI(opens in a new tab)
  3. REHAU – Premium-Fenstersystem ARTEVO(opens in a new tab)
  4. bauelemente bau – Rehau führt neues Fenstersystem Artevo offiziell ein(opens in a new tab)
  5. Gütegemeinschaft Kunststoff-Fensterprofilsysteme – Was ist Gütesicherung?(opens in a new tab)
  6. RENOLIT EXOFOL MX – Außenfolie mit Solar-Shield-Technologie(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Timber-Aluminium Windows: When Do They Pay Off?
Window profiles

Timber-Aluminium Windows: When Do They Pay Off?

Timber-aluminium windows: wood inside, aluminium shell outside. Construction, ventilation gap, care, insulation and cost – and when they really pay off.

6 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy