Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Energy & grants

Blower Door Test and the Window Connection: Finding Leaks Before They Get Expensive

7 minutes read

In a blower door test, a fan puts a building under 50 pascals of negative and positive pressure and measures how much air flows through leaks. The method is set out in DIN EN ISO 9972. The window connection is among the most common leakage points, above all the joint between frame and masonry. If you plan the test while the airtight layer is still accessible, you can fix faults cheaply.

The limits quoted below come from the German Building Modernisation Act (GModG) and apply to buildings in Germany. If your property is elsewhere, your national building regulations will set their own air-permeability requirements, so please check them locally.

Blower door test and windows: why airtightness counts

An airtight building envelope has three jobs:

  • Saving energy: Uncontrolled air flows carry warm air to the outside.
  • Avoiding structural damage: Warm, humid room air that flows through joints into cold components can condense there. That is exactly what happens at leaky window connections, with damp reveals and mould as the result.
  • Making ventilation plannable: Ventilation systems and ventilation concepts only work if the envelope is airtight.

The Building Modernisation Act (GModG, until July 2026 the Building Energy Act) requires in § 13 that the heat-transferring envelope surface, including joints, be permanently sealed airtight in line with the recognised rules of technology. The BEG minimum requirements also demand a thermal-bridge-minimised and airtight execution for all funded measures.

Limits: what the GModG says about the n50 value

If the airtightness of a new building is measured under DIN EN ISO 9972 and used in the energy balance, § 26 GModG sets the following limits at a pressure difference of 50 Pa:

Building Without mechanical ventilation system With mechanical ventilation system
up to 1,500 m³ heated air volume at most 3 air changes per hour (n50 ≤ 3.0 h⁻¹) at most 1.5 air changes (n50 ≤ 1.5 h⁻¹)
over 1,500 m³ at most 4.5 m³ per m² of envelope area per hour at most 2.5 m³ per m² of envelope area per hour

Measurements are taken under both negative and positive pressure. Passive houses and many funding programmes set much stricter requirements; the passive-house standard usually aims for an n50 value of around 0.6 h⁻¹.

How the measurement works

  1. Preparation: External doors and windows are closed, internal doors opened, and intentional openings such as ventilation systems are taped over or closed depending on the aim of the test.
  2. Fitting the fan: A frame with a sheet and fan is sealed into an external door or window.
  3. Pressure steps: The fan creates various pressure differences, up to at least 50 Pa, once under negative pressure and once under positive pressure.
  4. Evaluation: The n50 value results from the volume flow at 50 Pa and the building volume.
  5. Locating leaks: Under negative pressure, outside air flows in through leaks. The spots are found with an anemometer, smoke or thermography.

Typical leaks at the window

When leaks are located, windows regularly stand out. The most common places:

  • Connection joint between frame and masonry: If it was only foamed or only sealed with acrylic or silicone, these materials age and crack. 42watt describes exactly this as a typical weak spot in existing buildings.
  • Corners of the connection tapes: Foils and tapes that do not overlap cleanly in the corners or have torn.
  • Internal window cill connection: The airtight layer is often missing under the internal window board.
  • Roller shutter box: Old built-in boxes are often the biggest leak at the window, especially the inspection cover and the strap opening. More in the article Insulating roller shutter boxes.
  • Sash seals and hardware: Misaligned sashes or hardened seals. See Replacing window seals.

Tighter inside than outside: the principle at the connection

The three-layer principle applies to the window connection: airtight on the inside, thermal and acoustic insulation in the middle, driving-rain-tight but vapour-open on the outside. The foam in the joint fills and insulates; under this principle, lasting airtightness comes from a separate internal seal, a tape, a membrane or a suitable sealant connected cleanly to frame and wall. How the layers work together is explained in the article Sealed inside, open outside, and the installation basics in the article RAL installation.

The right time

The trade press points out that, under the current standard, the ideal time to measure is while the actual airtight layer is still accessible, that is before drylining or internal plaster. At the same time, there is a risk that membranes get damaged during later finishing work. Many clients therefore opt for two measurements:

  • A measurement during construction after the windows are fitted and the airtight layer is complete, to find and fix leaks.
  • A final measurement on the finished building, if proof is needed for the energy balance or funding.

According to energie-experten.org, early measurements avoid expensive rework because the leaks are then still openly accessible.

Blower door test when replacing windows in an existing building

In existing buildings the measurement is not compulsory but can be very revealing:

  • Before the replacement: shows how much leaks away through windows, roller shutter boxes and other places.
  • After the replacement: checks the quality of the installation before reveals are plastered.
  • With heat pumps: An airtight envelope lowers the heat load and with it the flow temperature required. Details in the article Heat pump and windows.

Because an existing building never becomes quite as airtight as a new one, the aim here is less about limits and more about finding gross leaks.

What to do if the connection leaks

If the testing contractor finds a leak at a window, the repair depends on the location:

  • Missing or torn internal seal: Reconnect tape or membrane cleanly to frame and wall. While the reveal is still open, this is possible with manageable effort.
  • Leaky corners: Add overlapping tapes in the corners, clean the adhesive surfaces first and prime them if necessary.
  • Leak under the window cill: Remove the internal window board and complete the lower connection.
  • Sash-to-frame joint: Adjust the hardware, check the seals; this belongs to the window, not the connection.
  • Roller shutter box: Seal the inspection cover, fit a brush seal to the strap opening or insulate the box.

It is important to check the spot again after the repair, for example with a short repeat measurement under negative pressure. Document the rectification with photos; this helps with later questions about warranty or funding.

Cost

The cost depends on building size, the number of measurements and the extent of leak location. 42watt gives roughly €300 to €700 for an average detached house; additional thermography costs a further €200 to €400. Obtain quotes from testing contractors, ideally with experience in DIN EN ISO 9972.

A tip for clients: agree in the contract with the window fitter that a measurement will take place during construction and that any leaks found at the window connection will be rectified. That creates clear responsibilities.

Checklist

  1. Define the aim of the test: proof for the energy balance, funding or quality control.
  2. Schedule it so that the airtight layer at the window is still accessible.
  3. Inform the window fitter about the planned measurement.
  4. Commission leak location with an anemometer, smoke or thermography.
  5. Fix any leaks found before reveals are lined.
  6. If needed, a final measurement on the finished building.

Airtight connections start with windows that suit the installation system. In the window configurator you choose profile, dimensions and accessories; for questions about connection profiles and installation situations, our team can help you via the contact page.

Frequently asked questions

Which n50 values apply under the German Building Modernisation Act?

If the airtightness of a new building is measured and used in the energy balance, the air volume flow at 50 Pa may be at most three times the heated air volume per hour, or 1.5 times with a ventilation system. For large buildings over 1,500 m³, limits related to the envelope area apply.

Is a blower door test compulsory when replacing windows?

Not for a plain window replacement in an existing building. It is useful for checking the quality of the connection, though, and is regularly required for efficiency-house refurbishments and new builds.

When should the blower door test take place?

Ideally while the airtight layer is still accessible, that is after the windows are fitted but before internal plaster, drylining and reveal linings. Leaks can then be fixed cheaply.

What does a blower door test cost?

The cost depends on building size, measuring method and leak location. The portal 42watt gives a range of roughly €300 to €700 for an average detached house; additional thermography costs extra.

Sources

  1. § 26 GModG – Prüfung der Dichtheit eines Gebäudes(opens in a new tab)
  2. § 13 GModG – Dichtheit(opens in a new tab)
  3. haustec: Anforderungen an Blower-Door-Tests – Messen nach neuer Norm(opens in a new tab)
  4. Ingenieurbüro n50: Anforderungen an die Luftdichtheit von Gebäuden(opens in a new tab)
  5. 42watt: Blower-Door-Test – Luftdichtheit für Wärmepumpen prüfen(opens in a new tab)
  6. energie-experten.org: Blower-Door-Test – Durchführung, Fehler und Kosten(opens in a new tab)
  7. BAFA: Technische Mindestanforderungen BEG EM (Kopie)(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Misted Double Glazing Between the Panes: What to Do
Energy & grants

Misted Double Glazing Between the Panes: What to Do

Pane misted between the glass? How to recognise a failed edge seal, why wiping does not help and when a glass replacement or a new window is worthwhile.

6 minutes read

Cover image: Vacuum Glazing: Thin Glass, Strong Insulation?
Energy & grants

Vacuum Glazing: Thin Glass, Strong Insulation?

Vacuum glazing explained: how vacuum insulating glass works, what FINEO and Pilkington Spacia deliver, where it helps in old buildings and where it falls short.

6 minutes read

Cover image: Condensation on Windows: Causes and Solutions
Energy & grants

Condensation on Windows: Causes and Solutions

Condensation on windows inside, outside or between the panes: what causes it, when it is harmless and what really helps against misted-up windows.

6 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy