Skip to content

Business customers only (B2B) · All prices net plus VAT

AluKun
Window profiles

uPVC Window Profiles Compared: How to Judge Frame Depth, Chambers and Insulation

6 minutes read

A uPVC window profile comparison should not stop at the number of chambers. What is most telling is the frame's Uf-value, the number of seal levels, the possible glass thickness and the frame depth – because they decide whether your window will later achieve the Uw-value required. Current systems range from 70 to 88 mm frame depth, and the differences are measurable.

What makes up a uPVC window profile

A window profile is an extruded hollow section made of PVC. The outer frame (fixed in the wall) and the sash frame (movable) together form the profile system. Inside are several air chambers, usually one of them with steel or fibre reinforcement for stability. Around the profile, the manufacturer defines the "system": seals, glazing beads, hardware groove, additional profiles such as frame extensions and the window-board connection profile.

Important for comparison: the figures in brochures always refer to a specific profile combination. Wording such as "Uf of up to …" describes the best case, not every version.

The five key figures in a uPVC window profile comparison

Frame depth

The frame depth is the depth of the outer frame from inside to outside. More depth creates room for additional chambers, a third seal and thicker triple glazing. It is not, however, a value that proves quality by itself – more on this in the article on frame depth in windows.

Chambers

Chambers interrupt the heat flow through the profile. Kömmerling quotes a 5-chamber construction for the 70 mm system and seven chambers for the 88 mm system; Schüco describes LivIng 82 as a 7-chamber system. The number of chambers is a design feature, not a measured value. How well the chambers insulate also depends on their geometry, the position of the reinforcement and any insulating inserts.

Seal levels

Rebate-seal systems have two seal levels (outer and inner); centre-seal systems have a third seal in the middle of the rebate. The centre seal divides the rebate space and improves thermal and sound insulation.

Uf-value

The Uf-value states how much heat is lost through the frame (in W/(m²K), lower is better). It is the most important comparison figure between profiles. How to read Uf-values correctly is explained in the article Uf-value of the frame.

Glass thickness

The glazing range shows which pane build-ups are possible. Thicker triple-glazed, acoustic or safety glass needs space in the rebate.

Manufacturer data compared directly

The following table summarises figures the manufacturers publish on their product pages and data sheets (as of September 2026). They are best values per version.

System Frame depth Seal Chambers Uf up to Glass thickness
Kömmerling 70 AD 70 mm Rebate 5 1.2 W/(m²K) 10–44 mm
Kömmerling 76 MD 76 mm Centre n/a 1.0 W/(m²K) 4–56 mm (offset sash)
Kömmerling 88 MD 88 mm Centre 7 0.93–0.98 W/(m²K) up to 60 mm
Schüco LivIng 82 AS 82 mm Rebate 7 1.0 W/(m²K) 16–54 mm
Schüco LivIng 82 MD 82 mm Centre 7 0.96 W/(m²K) 16–54 mm
REHAU Artevo 80 mm Centre 7 0.81 W/(m²K)* up to 56 / 72 mm

*REHAU quotes the value for the version with LowE technology. Glass thickness 56 mm with an offset sash, 72 mm with a flush sash.

Details of the Kömmerling systems are in the article Kömmerling 70, 76 or 88 – which profile suits?.

What the table does not show

Figures such as sound insulation and burglar resistance depend mainly on glass and hardware. Kömmerling quotes sound insulation values of up to 47 and 48 dB for 76 MD and 88 MD, and burglar resistance up to RC 2 with suitable equipment; Schüco states up to 47 dB and RC1N and RC2N for LivIng Classic. Such values are system possibilities – whether your window reaches them is decided by the equipment ordered. Also not shown are design lines: Kömmerling and Schüco offer offset and semi-offset sashes, aluminium cover shells and various sash contours that shape the appearance but can also affect the Uf-value and glazing rebate.

Which requirements the profile must meet

Anyone replacing windows in an existing residential building in Germany must, under Annex 7 of the Building Energy Act (GEG), achieve a Uw-value of at most 1.3 W/(m²K), 1.4 W/(m²K) for roof windows and 1.6 W/(m²K) for lift-and-slide or folding doors (as of September 2026). Practically all current systems with double or triple glazing achieve this. These are German requirements; in the UK, check the thermal requirements of the Building Regulations that apply to you.

Funding under the BEG

For BAFA funding of individual measures on the building envelope in Germany, the technical minimum requirements set a Uw of at most 0.95 W/(m²K). The basic funding rate is 15%; according to BAFA, the 5% iSFP bonus is granted only from an eligible minimum investment volume of €30,000 for buildings with one residential unit (as of September 2026). With a Uf-value around 1.0 W/(m²K) and good triple glazing, 0.95 is usually achievable; with a Uf of 1.2 it gets tight – then a lot depends on window size.

Quality assurance

According to the German uPVC window profile quality association (Gütegemeinschaft Kunststoff-Fensterprofilsysteme), Profine (Kömmerling), REHAU and Schüco Polymer Technologies hold systems with the RAL quality mark under RAL-GZ 716. The mark stands for initial testing and ongoing independent monitoring – a sensible minimum criterion in any comparison.

Typical mistakes of reasoning in profile comparisons

  • "More millimetres = better": an 88 mm profile is worthwhile if you need the insulation value. In a narrow reveal in an older building, a 76 mm system can be the better solution.
  • Confusing Uw and Uf: the Uw-value of the whole window depends strongly on glazing and spacer. A very good profile with plain double glazing will still miss the funding.
  • Brochure value as a guarantee: "Uf up to 0.93" applies only to a particular frame-sash combination. Coloured profiles, aluminium cover shells or wide mullions change the value.
  • Looking only at the profile: installation following the RAL guideline, connection sealing and hardware determine real-world performance just as much.

Which profile for which project?

Project Sensible profile class Reason
Cellar, garage, ancillary rooms 70 mm rebate seal Low frame depth, cost in focus
Renovation without funding 76 mm AD or MD Good ratio of insulation to frame depth
Renovation with BEG funding 76–82 mm MD Uw ≤ 0.95 W/(m²K) reliably achievable
New build, KfW efficiency house, near-passive house 80–88 mm MD Low Uf-values, thick triple glazing

This allocation is a guide. With large formats, or sound or burglar protection requirements, a higher class may be needed.

Checklist: how to compare quotes properly

  1. Ask for the Uw-value for your specific window dimensions, not just the standard value.
  2. Ask about the Uf-value and seal system of the profile combination offered.
  3. Check the glazing range if you want acoustic or safety glass.
  4. Clarify whether colour or decor affects the Uf-value or the reinforcement.
  5. Look for the RAL quality mark of the profile system.
  6. For funding: agree the Uw proof with the energy efficiency expert before applying.

In the AluKun configurator you select the profile system directly and see the specification per window. You will find an overview of all series on the windows page.

Frequently asked questions

Which uPVC window profile is the best?

There is no single best profile. What counts is the required Uw-value, the glazing you want, sash sizes, colour and installation situation. For funded projects in Germany, systems of 76 to 88 mm frame depth with a centre seal are usually considered.

Does the number of chambers say anything about insulation?

Only to a limited extent. More chambers tend to help, but what counts is the measured or calculated Uf-value of the frame. Two profiles with the same number of chambers can have markedly different Uf-values.

Is a 70 mm profile enough for a window replacement?

For the legal minimum under Germany's GEG (Uw of at most 1.3 W/(m²K) for residential buildings), it can be sufficient with suitable glazing. For German BEG funding with Uw of at most 0.95 W/(m²K), deeper profiles are generally the safer choice.

What does RAL-GZ 716 mean for uPVC profiles?

RAL-GZ 716 is the quality and testing specification for uPVC window profile systems. Systems with this quality mark undergo initial testing and ongoing independent monitoring, covering material, workmanship and function, among other things.

Sources

  1. Kömmerling 70 Anschlagdichtung Standard – Produktseite(opens in a new tab)
  2. Kömmerling 76 Mitteldichtung Standard – Produktseite(opens in a new tab)
  3. Kömmerling 88 Mitteldichtung – Produktseite(opens in a new tab)
  4. Schüco LivIng Classic – Datenblatt (PDF)(opens in a new tab)
  5. REHAU ARTEVO – Premium-Fenstersystem(opens in a new tab)
  6. GEG Anlage 7 – Höchstwerte der Wärmedurchgangskoeffizienten(opens in a new tab)
  7. BAFA – BEG Einzelmaßnahmen Gebäudehülle(opens in a new tab)
  8. Gütegemeinschaft Kunststoff-Fensterprofilsysteme – Profilsysteme mit RAL-Gütezeichen(opens in a new tab)

Ready for your project?

Configure your products to measure and see the price straight away – or send us your questions.

Cover image: Kömmerling 70: The 70 mm uPVC Profile Explained
Window profiles

Kömmerling 70: The 70 mm uPVC Profile Explained

Kömmerling 70 in review: 70 mm frame depth, 5 chambers, rebate seal and Uf up to 1.2 W/(m²K). Who the profile suits and where its limits lie.

6 minutes read

Cover image: Kömmerling 76: Centre Seal or Rebate Seal?
Window profiles

Kömmerling 76: Centre Seal or Rebate Seal?

Kömmerling 76 MD or AD? Uf-values, glass thicknesses, sound insulation and RC 2 compared – and which seal variant suits which house better.

6 minutes read

Cover image: Kömmerling 88: uPVC Profile for Passivhaus Needs
Window profiles

Kömmerling 88: uPVC Profile for Passivhaus Needs

Kömmerling 88 MD with 88 mm frame depth, 7 chambers and Uf from 0.77 W/(m²K): variants, Passivhaus versions, glass thicknesses and when the system pays off.

7 minutes read

We use strictly necessary cookies so the shop, configurator and basket work. With your consent we also use Google Analytics to measure how the site is used, and marketing signals for advertising. You can change your choice at any time in the footer. Read our privacy policy