Kömmerling 70: Technical Data, Applications and Limits of the 70 mm uPVC System
6 minutes read
Kömmerling 70 is the uPVC window system from Kömmerling (profine) with 70 mm frame depth, a 5-chamber construction and a rebate seal. The manufacturer quotes a Uf-value of up to 1.2 W/(m²K) and a glazing range of 10 to 44 mm. That makes the profile a solid choice where little installation depth is available or the legal minimum values suffice – for ambitious funding targets there are better-suited systems.
Kömmerling 70 in figures
The following details come from the manufacturer's product page for the "Kömmerling 70 Anschlagdichtung Standard" (rebate seal, standard) version (as of September 2026):
| Feature | Kömmerling 70 AD Standard |
|---|---|
| Frame depth | 70 mm |
| Chambers | 5-chamber construction |
| Sealing system | Rebate seal, two seal levels |
| Uf-value | up to 1.2 W/(m²K) |
| Glazing | 10 to 44 mm |
| Design | straight-lined, offset sash |
Kömmerling expressly describes the system for applications "where a small frame depth is an advantage". On the current manufacturer page, the rebate-seal "Standard" version is listed for the 70 mm platform.
How the rebate seal works
In a rebate-seal system there are two continuous seals in the window: an outer one on the outer frame and an inner one on the sash. Between them lies the rebate space in which the hardware sits. Water that gets in is drained outwards through drainage slots.
Compared with the centre seal, the third, central seal level is missing, which additionally divides the rebate space into a cold and a warm zone. Rebate-seal systems therefore generally reach somewhat higher (worse) Uf-values. The differences between the two principles are explained in detail in the article Centre seal vs rebate seal.
What does Uf 1.2 mean for the finished window Uw-value?
The Uf-value describes the frame only. For the whole window, the Uw-value is calculated under DIN EN ISO 10077-1 from the area proportions of glass and frame, their U-values and the thermal-bridge loss at the glass edge. On a typical living-room window the frame takes up about a quarter to a third of the area – the smaller the window, the greater its influence.
GEG requirement
When replacing windows in residential buildings in Germany, the GEG (Building Energy Act) requires a Uw-value of at most 1.3 W/(m²K) (Annex 7, as of September 2026). With triple glazing and a warm-edge spacer this is easily achievable with Kömmerling 70. The glazing range up to 44 mm leaves room for a usual triple build-up such as 4/16/4/16/4 mm. This is a German requirement; in the UK, check the Building Regulations thermal limits that apply to you.
BEG funding
For German BAFA funding, a Uw of at most 0.95 W/(m²K) applies. With a frame of Uf 1.2 W/(m²K), the glazing has to make up for the disadvantage. That can succeed with large windows with a high proportion of glass; with small formats it often gets tight. Have the Uw-value calculated for your specific dimensions before applying for funding. More on the funding conditions in the article BAFA funding for windows 2026.
Worked example for perspective
Imagine two windows of equal size with a single sash and identical triple glazing – one with Uf 1.2, one with Uf 1.0 W/(m²K). If the frame share is about 30% of the window area, the frame alone gives a difference of around 0.06 W/(m²K) in the Uw-value (0.2 × 0.3). That sounds small but can be exactly the gap between 0.98 and 0.92 – and thus decide eligibility for funding. With large windows with a slim frame share the effect shrinks; with small windows it grows. This example is a simplified rough calculation; the binding value comes from the calculation under the standard with your dimensions.
Steel reinforcement and colour
As with all uPVC windows, the stability of Kömmerling 70 depends on the reinforcement in the profile. Which reinforcement is used is determined by the window maker according to the system supplier's fabrication guidelines – depending on sash size, glass weight and colour. Dark decors heat up more in the sun than white profiles, so stricter requirements often apply to foil-laminated windows. More in the article Steel reinforcement in the uPVC window.
Where Kömmerling 70 plays to its strengths
Shallow reveal depth
In older buildings with an inner rebate or narrow masonry rebates, every millimetre of frame depth matters. A 70 mm frame leaves more room for an internal window board, insulation and the connection joint.
Ancillary and utility rooms
In unheated or little-heated rooms – garage, cellar, workshop, store room – insulation value is less important. What counts here is robustness, tightness and a reasonable price.
Uniform look
If you combine several window systems in a house, you often want a uniform external appearance. The offset sash of the 70 system matches the classic uPVC window look.
Limits of the system
- Funding targets: for Uw ≤ 0.95 W/(m²K) the 76 and 88 mm systems offer more reserve.
- Thick special glass: acoustic or safety glass with a large build-up can exceed the range up to 44 mm.
- Two seal levels: in heavy road noise or exposed locations with driving rain, a centre seal has a design advantage.
- Passive-house or efficiency-house new builds: deeper systems with lower Uf-values are the rule here.
Installation: what matters with a 70 mm frame
A small frame depth offers less area for sealing tapes and fixing. So plan the installation deliberately:
- Position in the wall: the frame should sit as far as possible in the insulation plane or close to the outer edge of the masonry so that the isotherm does not run through the reveal.
- Connection joint: inside an airtight tape, in the middle insulation, outside a driving-rain-tight, vapour-permeable seal.
- Window board connection: the window-board connection profile under the frame belongs to the system and is ordered with it.
- Fixing: frame plugs or installation screws at the spacings specified by the system supplier, load-bearing packers under the load points.
Kömmerling 70 compared with 76 and 88
| System | Frame depth | Seal | Uf up to | Glass up to |
|---|---|---|---|---|
| Kömmerling 70 AD | 70 mm | Rebate | 1.2 W/(m²K) | 44 mm |
| Kömmerling 76 AD | 76 mm | Rebate | 1.1 W/(m²K) | 52 mm (sash 76223: 58 mm) |
| Kömmerling 76 MD | 76 mm | Centre | 1.0 W/(m²K) | 56 mm |
| Kömmerling 88 MD | 88 mm | Centre | 0.93–0.98 W/(m²K) | 60 mm |
All values according to manufacturer data (as of September 2026). Which platform suits which building is compared in the article Kömmerling 70, 76 or 88.
Checklist: does Kömmerling 70 suit your project?
- Do you need funding? If so, request a Uw calculation for your dimensions or choose a deeper system straight away.
- How deep is the reveal? Where space is tight, the small frame depth is a real advantage.
- Which glass function? Check acoustic and safety glass for fit within the 10–44 mm range.
- Which room? For ancillary rooms and cellars the system is often entirely sufficient.
- Plan the installation: a good profile needs a professional, airtight connection following the principle "tighter inside than outside".
You can put together the uPVC windows in the AluKun range in the configurator by profile system, size, colour and glazing. If you are unsure whether 70 mm is enough for your project, tell us the dimensions and target Uw – we will tell you which combination fits.
Frequently asked questions
What Uf-value does Kömmerling 70 have?
Kömmerling states a Uf-value of up to 1.2 W/(m²K) for the Kömmerling 70 system in its standard version. The actual value depends on the frame-sash combination.
Can Kömmerling 70 be ordered with triple glazing?
Yes. The manufacturer quotes a glazing range of 10 to 44 mm, which is enough for usual triple-glazed units. Very thick acoustic or safety build-ups may no longer fit.
Is Kömmerling 70 eligible for funding?
For German BEG funding of individual measures the window must achieve a Uw-value of at most 0.95 W/(m²K). With a frame Uf of up to 1.2 W/(m²K) that is only possible with very good glazing and favourable sizes; deeper profiles are usually the safer choice.
What is Kömmerling 70 particularly suited to?
Installation situations with little space in the reveal, ancillary rooms, cellars and garages, and projects where the legal GEG requirement rather than funding is decisive.
Sources
- Kömmerling 70 Anschlagdichtung Standard – Produktseite(opens in a new tab)
- Kömmerling – 70-mm-Systeme(opens in a new tab)
- GEG Anlage 7 – Höchstwerte der Wärmedurchgangskoeffizienten(opens in a new tab)
- BAFA – BEG Einzelmaßnahmen Gebäudehülle(opens in a new tab)
- Baunetz Wissen – U-Wert und Wärmedurchgangskoeffizient(opens in a new tab)
Ready for your project?
Configure your products to measure and see the price straight away – or send us your questions.